EasyManuals Logo
Home>GE>Refrigerator>GBS22**P

GE GBS22**P User Manual

GE GBS22**P
31 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #20 background imageLoading...
Page #20 background image
FREEZER
DISPLAY
FRESH
FOOD
DISPI-AY
DIAGNOSTICS
RESULTS
COMMENTS
0
c
Encoder
Test
As
the knob is
rotated
the
d'splay will
show the
corresponding
setting
Only
for models
with
temperature
control knobs
0
7
Control
and
Sensor
System
Test
Checks
each
thermistor
and
displays
"P"
for
pass
and
"0"
for fail
See Note
1
below
for display
order
1
0
Dampers
Test
Opens
each damper,
pauses
briefly
and then
closes.
lncludes
Custom
Cool
dampers if
applicable
1
Fan Test
Runs
each fian
in
sequence
for 10
seconds
each.
1
2
100%
Run Time
Sealed
system
on
100%
ofthe
time.
Times out
after t hour.
1
3
Prechill
Test
Starts
Prechill
mode.
Unit
retums
to normal
on its
own.
,|
4
Defrost Test
Toggles
on the Defrost
cycle.
See
Note
2 below
Must
press
again to tum
heaters
off. See Note
2
1
5
Main
Confol Reset
Causes
a system reset
1
6
Exit Diagnostic
Mode
Causes a temperature
control board reset
1
7
Degrees
C'/Fo
Changes
ftom F'to
C' or C'
to
F"
on
temperature
display
See Note
3
belour
Note
1 .
#1 &#2
-
Single Fresh
Food
Thermistor
#3
-
Custom
Cool #4
-
Evaporator
#5
-
Freezer
Thermistortestresultsare:
P
=
Pass
0
=
Fail
S
=
Shortto
5VDC B
=
Bad
amplifier(replace
main
control)
Note
2. You
must
enter
the
defrost test
again
to toggle
the defrost
heater
off
at the
end of the
test. The
heater
will
not
come
on if the
evaporator
thermistor
is
warm.
Note
3. Press
FF
temperatrire pad
(warmer/colder)
to
toggle.
Using the
service
test
board,
you
can
change
the
temperature
display
from Fahrenheit
to Centigrade
on the refrigerator
display,
but the
customer
will
be
unable to
change
it back
without
using
a service
test
board.
Refer
to Service
Guide
31-9072 for
additional information
Gondenser
Fan
Noise
Symptom:
Loud
airflow
noise
coming
from
the
condenser
fan
compartment.
Problem:
The
plenum
is
bent
out of
position
due
to
the screw
tab being
tightened
at an
angle.
Solution:
Release
the
tension
off the
plenum
by
loosening
the
screw
tab.
Straighten
the
plenum
to
the
proper
position
around the
fan
blade.
Tighten
the screw
so the
tab is
straight.
Photo
Shown
with
Plenum
in the
Bent Position
-19-

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the GE GBS22**P and is the answer not in the manual?

GE GBS22**P Specifications

General IconGeneral
BrandGE
ModelGBS22**P
CategoryRefrigerator
LanguageEnglish

Related product manuals