Gigabyte G1.Sniper 3 User Manual

- 20 -Hardware Installation
External SATA Connector
Power Connector
External SATA
Connector
SATA Bracket
SATA Signal Cable
SATA Power Cable
1-7 Installing the SATA Bracket
Turn off your system and the power switch on the power supply before installing or removing the •
SATA bracket and SATA power cable to prevent damage to hardware.
Insert the SATA signal cable and SATA power cable securely into the corresponding connectors •
when installing.
The SATA bracket allows you to connect external SATA device(s) to your system by expanding the internal
SATA port(s) to the chassis back panel.
Follow the steps below to install the SATA bracket:
The SATA bracket includes one SATA bracket, two SATA
signal cables, and one SATA power cable.
Step 2:
Connect the SATA
cable from the bracket
to the SATA port on
your motherboard.
Step 4:
Plug one end of the
SATA signal cable
into the external SATA
co nn ector on th e
bracket. Then attach
the SATA power cable
to the power connector
on the bracket.
Step 1:
Locate one free slot
and secure the SATA
bracket to the chassis
back panel with a
screw.
Step 3:
Connect the power
cable from the bracket
to the power supply.
Step 5:
Connect the other ends of the SATA signal cable and SATA power cable to your
SATA device. For SATA device in external enclosure, you only need to connect
the SATA signal cable. Before connecting the SATA signal cable, make sure to
turn off the power of the external enclosure.

Gigabyte G1.Sniper 3 Specifications

General

ECC	No
Non-ECC	Yes
Memory voltage	1.5 V
Memory channels	Dual-channel
Number of memory slots	4
Supported memory types	DDR3-SDRAM
Maximum internal memory	32 GB
Supported memory clock speeds	1066, 1333, 1600 MHz
Supported memory module capacities	16GB, 1GB, 2GB, 4GB, 8GB
System bus rate	5 GT/s
Processor socket	LGA 1155 (Socket H2)
Processor manufacturer	Intel
Compatible processor series	Intel Core i3, Intel Core i5, Intel Core i7
Maximum number of SMP processors	1
USB 2.0 connectors	2
Number of SATA III connectors	6
Number of Parallel ATA connectors	0
Headphone outputs	5
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Audio chip	Creative CA0132
Cooling type	Passive
Component for	PC
Power source type	ATX
Motherboard chipset	-
PC health monitoring	CPU, FAN, Temperature
Audio output channels	7.1 channels
Motherboard form factor	XL-ATX
RAID levels	0, 1, 5, 10
Supported storage drive interfaces	SATA II, SATA III
Cables included	SATA
Graphics card	HD Graphics
OpenGL version	3.2
DirectX version	11
Maximum graphics card memory	1696 MB
Parallel processing technology support	2-Way SLI, 3-Way SLI, 4-Way SLI, Hybrid CrossFireX
PCI Express slots version	3.0
Controller interface type	Intel Z77
Controller 2nd interface type	2 x Marvell 88SE9172
Wi-Fi standards	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Bluetooth version	4.0
Networking features	10/100/1000 Mbit/sec
Ethernet interface type	Gigabit Ethernet
BIOS type	EFI AMI
ACPI version	2.0a
BIOS memory size	64 Mbit

Weight and Dimensions

Depth	264 mm
Width	305 mm