Gigabyte G1.Sniper 3 User Manual (English)

To Next Page

To Previous Page

BIOS Setup - 58 -

OnBoard LAN Controller#1 (Qualcomm Atheros Killer E2201 LAN Chip, LAN1) &

Enables or disables the Qualcomm Atheros Killer E2201 LAN function. (Default: Enabled)

If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to

Disabled.

Intel(R) Smart Connect Technology `

ISCT Conguration &

Enables or disables Intel Smart Connect Technology. (Default: Disabled)

Marvell ATA Controller Conguration `

GSATA Controller (Marvell 88SE9172 Chip, GSATA3 6 and GSATA3 7 connectors) &

Enables or disables RAID for the SATA controllers integrated in the Marvell 88SE9172 chip or congures

the SATA controllers to AHCI mode. The area below displays the current status of the two SATA ports.

IDE Mode Disables RAID for the SATA controllers and congures the SATA controllers to IDE 

mode.

AHCI Mode Congures the SATA controllers to AHCI mode. Advanced Host Controller Interface 

(AHCI) is an interface specication that allows the storage driver to enable advanced

Serial ATA features such as Native Command Queuing and hot plug. (Default)

RAID Mode Enables RAID for the SATA controllers. 

Disabled Disables this function. 

GSATA Controller (Marvell 88SE9172 Chip, GSATA3 8 and GSATA3 9 connectors) &

Enables or disables RAID for the SATA controllers integrated in the Marvell 88SE9172 chip or congures

the SATA controllers to AHCI mode. The area below displays the current status of the two SATA ports.

IDE Mode Disables RAID for the SATA controllers and congures the SATA controllers to IDE 

mode.

AHCI Mode Congures the SATA controllers to AHCI mode. Advanced Host Controller Interface 

(AHCI) is an interface specication that allows the storage driver to enable advanced

Serial ATA features such as Native Command Queuing and hot plug. (Default)

RAID Mode Enables RAID for the SATA controllers. 

Disabled Disables this function. 

Other manuals for Gigabyte G1.Sniper 3

User Guide6 pages

Need help?

Do you have a question about the Gigabyte G1.Sniper 3 and is the answer not in the manual?

Gigabyte G1.Sniper 3 Specifications

General

ECC	No
Non-ECC	Yes
Memory voltage	1.5 V
Memory channels	Dual-channel
Number of memory slots	4
Supported memory types	DDR3-SDRAM
Maximum internal memory	32 GB
Supported memory clock speeds	1066, 1333, 1600 MHz
Supported memory module capacities	16GB, 1GB, 2GB, 4GB, 8GB
System bus rate	5 GT/s
Processor socket	LGA 1155 (Socket H2)
Processor manufacturer	Intel
Compatible processor series	Intel Core i3, Intel Core i5, Intel Core i7
Maximum number of SMP processors	1
USB 2.0 connectors	2
Number of SATA III connectors	6
Number of Parallel ATA connectors	0
Headphone outputs	5
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Audio chip	Creative CA0132
Cooling type	Passive
Component for	PC
Power source type	ATX
Motherboard chipset	-
PC health monitoring	CPU, FAN, Temperature
Audio output channels	7.1 channels
Motherboard form factor	XL-ATX
RAID levels	0, 1, 5, 10
Supported storage drive interfaces	SATA II, SATA III
Cables included	SATA
Graphics card	HD Graphics
OpenGL version	3.2
DirectX version	11
Maximum graphics card memory	1696 MB
Parallel processing technology support	2-Way SLI, 3-Way SLI, 4-Way SLI, Hybrid CrossFireX
PCI Express slots version	3.0
Controller interface type	Intel Z77
Controller 2nd interface type	2 x Marvell 88SE9172
Wi-Fi standards	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Bluetooth version	4.0
Networking features	10/100/1000 Mbit/sec
Ethernet interface type	Gigabit Ethernet
BIOS type	EFI AMI
ACPI version	2.0a
BIOS memory size	64 Mbit