EasyManuals Logo
Home>Gigabyte>Motherboard>GA-P31-ES3G

Gigabyte GA-P31-ES3G User Manual

Gigabyte GA-P31-ES3G
84 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #42 background imageLoading...
Page #42 background image
GA-P31-ES3G Motherboard - 42 -
2-6 Power Management Setup
CMOS Setup Utility-Copyright (C) 1984-2008 Award Software
Power Management Setup
ACPI Suspend Type [S3(STR)]
Soft-Off by PWR-BTTN [Instant-Off]
PME Event Wake Up [Enabled]
Power On by Ring [Enabled]
Resume by Alarm [Disabled]
x Date (of Month) Alarm Everyday
x Time (hh:mm:ss) Alarm 0 : 0 : 0
HPET Support
(Note)
[Enabled]
HPET Mode
(Note)
[32-bit mode]
Power On By Mouse [Disabled]
Power On By Keyboard [Disabled]
x KB Power ON Password Enter
AC Back Function [Soft-Off]
KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Item Help
Menu Level`
ACPI Suspend Type
Specifies the ACPI sleep state when the system enters suspend.
S1(POS) Enables the system to enter the ACPI S1 (Power on Suspend) sleep state.
In S1 sleep state, the system appears suspended and stays in a low power
mode. The system can be resumed at any time.
S3(STR) Enables the system to enter the ACPI S3 (Suspend to RAM) sleep state (default).
In S3 sleep state, the system appears to be off and consumes less power than
in the S1 state. When signaled by a wake-up device or event, the system
resumes to its working state exactly where it was left off.
Soft-Off by PWR-BTTN
Configures the way to turn off the computer in MS-DOS mode using the power button.
Instant-Off Press the power button and then the system will be turned off instantly. (Default)
Delay 4 Sec. Press and hold the power button for 4 seconds to turn off the system. If the power
button is pressed for less than 4 seconds, the system will enter suspend mode.
PME Event Wake Up
Allows the system to be awakened from an ACPI sleep state by a wake-up signal from a PCI or
PCIe device. Note: To use this function, you need an ATX power supply providing at least 1A on
the +5VSB lead. (Default: Enabled)
Power On by Ring
Allows the system to be awakened from an ACPI sleep state by a wake-up signal from a modem
that supports wake-up function. (Default: Enabled)
(Note) Supported on Windows
®
Vista
®
operating system only.

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Gigabyte GA-P31-ES3G and is the answer not in the manual?

Gigabyte GA-P31-ES3G Specifications

General IconGeneral
Memory voltage1.8 V
Number of memory slots2
Maximum internal memory4 GB
Processor socketLGA 775 (Socket T)
Processor manufacturerIntel
USB 2.0 connectors8
Power fan connectorYes
Number of SATA connectors4
Number of Parallel ATA connectors1
S/PDIF in portNo
Headphone outputs3
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Firewire (IEEE 1394) ports0
Audio chipRealtek ALC888
Audio output channels5.1 channels
Motherboard form factorATX
Compatible operating systemsMicrosoft Windows Vista, XP, 2000
BIOS typeAWARD
LAN controllerRealtek RTL8111C
Networking features10/100/1000 Mbit
Trial softwareNorton Internet Security
Weight and Dimensions IconWeight and Dimensions
Depth194 mm
Width305 mm

Related product manuals