How to Keep Your Dishwasher in Shape
After Every Wash
After every wash, turn off the water supply
to the appliance and leave the door slightly
ajar so that moisture and odors are not
trapped inside.
Remove the Plug
Before cleaning or performing
maintenance, always remove the plug from
the socket. Do not run risks.
No
Solvents
or Abrasive Cleaning
To clean the exterior and rubber parts of
the dishwasher, do
not
use solvents or
abrasive cleaning products.
Use
only
a
cloth and warm soapy water. To remove
spots or stains from the surface of the
interior, use a cloth dampened
with
water
and a little white vinegar,
or
a cleaning
product made specifically for dishwashers.
Â
Attention:
The installation of
the pipes
and electrical equipments
should be done by professionals.
li
a.
Installation
When You Go on holiday
When you go on holiday, it is
recommended that you run a wash
cycle with the dishwasher empty and
then remove the plug from the socket,
turn off the water suppl y and leave the
door of the appliance slightly ajar. This
will help the seals last longer and
prevent odors from forming in the
appliance.
Moving theAppliance
If the appliance must be moved, try to
keep it in the vertical position. If
absolutely necessary, it can be
positioned on its back.
Seals
One
of the
factors
that
cause odors
to
form in the
dishwasher is food that
remains trapped in the seals. Periodic
cleaning with a damp sponge will
prevent this.
Â
Warning
Electrical Shock Hazard!
Disconnect electrical power before
installing dishwasher.
Failure
to
do so can result in death or
electrical shock.
A
Keep this instruction manual in a safe place for future reference.
If
the appliance is sold,
given away or moved, please ensure
the
manual is kept with the machine, so that the
new owner may benefit from the advice contained within it.
A
Please read this instruction manual carefully: it contains important information regarding
the safe installation, use and maintenance of the appliance.
A
If
the appliance
must be moved at any time, keep it
in an upright position; if absolutely
necessary,
it
may be tilted onto its back.
Positioning and leveling
1. Remove the appliance from all packaging and check that it has not been damaged during
transportation. If it has been damaged, contact the retailer and do not proceed and further
with the installation process.
2. Check the dishwasher by placing it so that its sides or back panel are in contact with the
adjacent cabinets or even with the wall. This appliance can also be recessed under a single
worktop.
3. Position the dishwasher on a level and sturdy floor. If the floor is uneven, the front feet of the
appliance may be adjusted until it reaches a horizontal position (the angle of inclination must not
exceed
2 degrees). If the appliance is levelled correctly, it will
be
more stable and much
less
likely to
move or cause vibrations and noise while it is operation.
Connecting the water and electricity supplies
A
Connection
to the water
and electricity supplies should only be performed
by a qualified
technician.
A
The
dishwasher should not stand on
top of the
water hoses or
the
electricity supply cable
A
The appliance must be connected to the water supply network using new piping. Do
not
use
old piping.
* Connecting the water in let hose
Connecting the water outlet hose
Electrical connection
Connect the cold water supply hose
to
a threaded
3/4(inch)
connector and make sure that it is fastened tightly in place.
If the water pipes are new or have not been used for an
extended period of time, let the water run to make sure that
the water is clear and free of impurities. If this precaution is
not taken, there is a risk that the water inlet can get blocked
and the appliance could be damaged.
Fit
the
drainage hose
of
your machine
to the
drainage
pipe
without bending.
If the length of the hose is not sufficient, apply to the
authorized service for an extension made from the same
material as the original. Remember that the length of the
hose should not exceed 4meters even when with
an
extension.
If the drainage hose is longer the 4 m. the dishes will not
be cleaned properly secure your hose firmly to the drainage
pipe to avoid it coming off during the washing process.
Before inserting the plug into the electrical socket, make sure that:
ethe socket is earthed and complies with current regulations;
ethe socket can withstand
the
maximum load of the appliance, which is indicated on the data plate
located on the inside of the door(see description of the appliance);
ethe power supply voltage falls within the values indicated on the data plate on the inside of the door;
ethe socket is compatible with the plug of
the
appliance. If this is not
the
case, ask an authorised
technician to replace the plug (see assistance); do not use extension cables or multiple sockets.
_*_F_o,_o_p_tio_n_a_l -----------------------------
To Next Page
Loading...
Need help?
General
