EasyManuals Logo
Home>Harman Kardon>Receiver>AVR 1610

Harman Kardon AVR 1610 Quick Start Guide

Harman Kardon AVR 1610
11 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #4 background imageLoading...
Page #4 background image
AVR
4
Connections
Connect Your Speakers
How to use the AVR speaker terminals:
1. Unscrew Cap 2. Insert Bare Wire 3. Tighten Cap
Always connect the colored (+) terminal on the AVR to the (+) terminal on the speaker
(usually red), and the black (–) terminal on the AVR to the (–) terminal on the speaker
(usually black).
IMPORTANT: Make sure the ( + ) and ( – ) bare wires do not touch each other or the other
terminal. Touching wires can cause a short circuit that can damage your AVR.
Connect the speakers as shown in the illustration.
SL
FHL
SR
FHR
FRFL
C
SBL SBR
AVR 1710/AVR 171 Only:
Connect Surround Back L/R Speakers
-OR- Front Height L/R Speakers Here
Connect Your Subwoofer
Use a single RCA audio cable to connect your subwoofer to AVR’s Subwoofer
Pre-Out connector, as shown in the illustration below. (For the AVR 1710/AVR 171 you
can use either the Subwoofer 1 or Subwoofer 2 connector when you’re using a single
subwoofer, or you may connect two subwoofers for increased bass performance in larger
listening rooms.) Consult your subwoofer’s user manual for specic information about
making connections to it.
AVR 1710/
AVR 171
AVR 1610/AVR1510/
AVR 161/AVR 151
Powered
Subwoofer
Single
RCA Audio Cable
(not supplied)
Use either
connector
Connect Your TV or Video Display
If your TV has an HDMI connector: Use an HDMI cable (not included) to connect it to
the AVR’s HDMI Out connector. (For the AVR 1710/AVR 171 you can use either HDMI Out
connector.) You do not need to make any other connections to your TV from the AVR or
from any of your video source components.
AVR 1710/AVR 171
AVR 1610/AVR 161/
AVR 1510/AVR 151
TV
HDMI Cable
(not supplied)
Use either
connector
AVR 1710/AVR 171 only: Connect a single TV to the HDMI Out 1 connector. If you have a
second TV you can connect it to the AVR’s HDMI Out 2 connector. Both TVs will display the
same picture, but the HDMI Out 2 connector will not output the AVR’s on-screen display
and does not have Audio Return Channel capability (see below).
Note: If your TV is equipped with the HDMI Audio Return Channel function, you can feed
its sound to the AVR via the HDMI Out connector’s Audio Return Channel, and it will not
require additional audio connections to the AVR. (For the AVR 1710/AVR 171 the ARC is
available only on the HDMI Out 1 connector.)

Other manuals for Harman Kardon AVR 1610

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Harman Kardon AVR 1610 and is the answer not in the manual?

Harman Kardon AVR 1610 Specifications

Audio Specifications IconAudio Specifications
stereo power85W per channel, two channels driven @ 6/8 ohms, 20Hz – 20kHz, <0.1% THD
multichannel power85W per channel, two channels driven @ 6/8 ohms, 20Hz – 20kHz, <0.1% THD
input sensitivity/impedance250mV/27k ohms
signal-to-noise ratio (IHF-A)100dB
surround system adjacent channel separation (Dolby Pro Logic/DPLII)40dB
surround system adjacent channel separation (Dolby Digital)55dB
surround system adjacent channel separation (DTS)55dB
frequency response (@1W)10Hz – 130kHz (+0dB/–3dB)
high instantaneous current capability (HCC)±29 amps
slew rate40V/sec
FM Tuner Specifications IconFM Tuner Specifications
frequency range87.5MHz – 108.0MHz
usable sensitivity IHF1.3µV/13.2dBf
signal-to-noise ratio (mono/stereo)70dB/68dB
distortion (mono/stereo)0.2%/0.3%
stereo separation40dB @1kHz
selectivity (±400kHz)70dB
image rejection80dB
IF rejection80dB
AM Tuner Specifications IconAM Tuner Specifications
frequency range520kHz – 1, 610kHz
signal-to-noise ratio38dB
usable sensitivity (loop)425µV
distortion (1kHz, 50% mod)1.0%
selectivity (±10kHz)30dB
Video Specifications IconVideo Specifications
television formatNTSC
input level/impedance1Vp-p/75 ohms
output level/impedance1Vp-p/75 ohms
video frequency response (composite video)10Hz – 8MHz (–3dB)
HDMI supportup to 4K x 2K
General Specifications IconGeneral Specifications
power requirement120V AC/60Hz
power consumption<0.5W (standby); 450W maximum
dimensions (H x W x D)4-3/4" x 17-5/16" x 11-13/16" (121mm x 440mm x 300mm)
weight10lb (4.6kg)

Related product manuals