CONNECTIONS
Digital Audio
The AVR 460/AVR 360 is equipped with four HDMI (High-Definition
Multimedia Interface) inputs, and one output. HDMI technology enables
digital audio and video information to be carried using a single cable,
delivering the highest quality picture and sound.
The AVR 460/AVR 360 uses HDMI (V.1.3a with Deep Color) technology and
is capable of processing both the audio and video components of the HDMI
data, minimizing the number of cable connections in your system. The
AVR 460/AVR 360 implements Deep Color, which increases by an order of
magnitude the shades of color that can be displayed, and the latest lossless
multichannel audio formats, including Dolby TrueHD and DTS-HD Master
Audio.
NOTE
: Some DVD-Audio, SACD, Blu-ray Disc and HD-DVD players only
output multichannel audio through their multichannel analog outputs.
Make a separate analog audio connection in addition to the HDMI
connection, which is still used for video and to listen to Dolby Digital, DTS
or PCM materials that may be stored on the disc.
The AVR 460/AVR 360 converts analog video signals to the HDMI format,
including its on-screen menus, upscaling to high-definition 1080p resolution.
The HDMI connector is shaped for easy plug-in (see Figure 4). If your video
display has a DVI input and is HDCP-compliant, use an HDMI-to-DVI adapter
(not included). A separate audio connection is required. HDMI cable runs are
limited to about 3 meter.
Figure 4 – HDMI Connection
If your video display or source device is not HDMI-capable, use one of the
analog video connections (composite or component video) and a separate
audio connection.
Coaxial digital audio jacks are usually color-coded in orange. Although they
look similar to analog jacks, you should not connect coaxial digital audio
outputs to analog inputs or vice versa. See Figure 5.
Coaxial
Coaxial digital
audio cable
Figure 5 – Coaxial Digital Audio
Optical digital audio connectors are normally covered by a shutter to protect
them from dust. The shutter opens as the cable is inserted. Input connectors
are color-coded using a black shutter, while outputs use a gray shutter. See
Figure 6.
Optical
Optical digital
audio cable
Figure 6 – Optical Digital Audio
Analog Audio
Two-channel analog connections require two cables, one for the left channel
(white) and one for the right channel (red). These two cables are often
attached to each other. See Figure 7.
For sources that are capable of both digital and analog audio, you may make
both connections.
The analog audio connection is required for multizone operation, as the
AVR 460/AVR 360’s multizone system is not capable of converting a digital
signal to analog format. Use the analog audio connections even with the
Surround Back/Zone 2 speaker outputs, in case another 2-channel digital
audio source is in use in the main listening area. The AVR 460/AVR 360 is only
capable of processing one PCM source at a time.
You may only record materials from DVDs or other copy-protected sources
using analog connections. Remember to comply with all copyright laws, if
you choose to make a copy for your own personal use.
Analog audio
cable (RCA)
L
R
Figure 7 – Analog Audio
The 6/8-Channel Inputs are multichannel analog connections that are used
with high-definition sources that decode the copy-protected digital content,
such as some DVD-Audio, SACD, Blu-ray Disc and HD-DVD players (See Figure
8). The multichannel analog audio connection is not required for players
compliant with HDMI version 1.1 or better, or that output linear PCM signals
via an HDMI connection. Consult the owner’s guide for your disc player for
more information.
Multichannel
analog audio
cable (RCA)
Front Surround Center
White Blue Green
Red Gray Purple
Subwoofer
Figure 8 – Multichannel Analog Audio
The AVR 460/AVR 360 also includes a proprietary, dedicated audio connection
for The Bridge III docking station for iPod or iPhone. If you own a docking
iPod (most models, 4G or later), iPhone or iPhone 3G, connect The Bridge III
to The Bridge III port on the receiver. See Figure 9. Dock your iPod or iPhone
(not included) in The Bridge III, and you may listen to your audio materials
through your high-performance audio system. You may view still images
or video materials stored on a photo- or video-capable iPod that supports
video browsing, or an iPhone. Use the AVR 460/AVR 360 remote to control
the device, with navigation messages displayed on the front panel and on a
video display connected to the AVR. The Bridge III outputs analog audio to the
AVR 460/AVR 360, and is available to the multiroom system.
Figure 9 – The Bridge III port
To Next Page
Loading...
Need help?
General
Weight and Dimensions
