HART HPSV25 User Manual

7 – English
MAINTENANCE
WARNING:
Ifproductisnotworkingasitshould,hasbeendropped,
damaged,leftoutdoors,ordroppedintowater,takeit
toaservicecenterpriortocontinuinguse.
WARNING:
Haveservicingperformedbyaqualifiedrepairperson
usingonlyidenticalreplacementparts.Thiswillensure
thatthesafetyoftheproductismaintained.
WARNING:
Any other servicing should be performed by an
authorizedservicerepresentative.
Themotorandbrushrollareequippedwithbearingswhich
containsufficientlubricationfortheirlifetime.Theaddition
oflubricantcouldcausedamage.Donotaddlubricantto
motororbrushroll.
GENERAL MAINTENANCE
Avoidusing solvents when cleaning plastic parts. Most
plasticsaresusceptibletodamagefromvarioustypesof
commercialsolventsandmaybedamagedbytheiruse.Use
cleanclothstoremovedirt,dust,oil,grease,etc.
NOTICE:
Athermalprotectorhasbeendesignedintoyourcleaner
toprotectitfromoverheating.Whenthethermalprotector
activatesthecleanerwillstoprunning.
Ifthishappensproceedasfollows:
 TurncleanerOFFandremovebatterypack.
 EmptyDustBowl.
 Inspect the Beater Bar, roller brushes, separator
assembly,filterforanyobstructions.Clearobstructions
ifpresent.
 When cleaner is de-energized and motor cools for
30minutes,thethermalprotectorwilldeactivateand
cleaningmaycontinue.
If the thermal protector continues to activate after
followingtheabovesteps,yourcleanerneedsservicing.
WARNING:
Donotatanytimeletbrakefluids,gasoline,petroleum-
basedproducts,penetratingoils,etc.,comeincontact
withplasticparts.Chemicalscandamage,weakenor
destroyplasticwhichcouldresultinseriouspersonal
injury.
CAUTION:
Toreducetheriskofinjuryfrommovingparts-Remove
batterybeforeservicing.”
REMOVING THE ROLLER BRUSHES FOR
CLEANING
See Figures 9 - 11, page 11.
Therollerbrushesarelocatedinsidethebeaterbar.The
rollerbrusheshaveatool-freeendcap,allowingittobe
easilyremovedforcleaning.
To remove:
 Removethebatterypack.
 Rotatetheendcapapproximately1/4in.counterclockwise
tounlocktherollerbrush.
NOTE:Ifdesired,insertacoinintotheslotontheendof
therollerbrushandrotate.
 Slidethebrushtoreleasethecapandpullthebrushfrom
thebeaterbarassembly.
NOTE:Use scissors to remove any threads or hair
wrappedaround the roller brush using the scissor
grooves.Useaclothorpapertoweltowipetheroller
brushclean.
To reattach:
 Inserttherollerbrushintothebeaterbarassembly.
 Alignthetabsonthecaptothenotchesontheassembly
andfirmlypressthecapintoplace.
NOTE:Makesuretheoppositeendoftherollerbrushis
alignedtothedrivespindlewhenpressingthecapinto
theassemblyhousing.
 Turntheendcapclockwiseuntilitclicksintothelocked
position.
To remove the plush roller brush from the beater bar:
 Insertacoinintotheslotontheendoftherollerbrush.
Rotatetheendcapapproximately1/4in.counterclockwise
tounlocktheplushrollerbrush.
 Rotate the plush roller brush away from the beater bar
assembly.

HART HPSV25 Specifications

General

Brand	HART
Model	HPSV25
Category	Vacuum Cleaner
Language	English