15 16
Draining residual water
Before emptying the residual water, switch the appliance off and unplug it from the
mains socket. Remove the plinth. Place a container beneath it.
Open the filter but do not remove it completely. Slowly turn the filter
counterclockwise until the water begins to drain out.
Wait until all the water has drained.
Now unscrew the filter completely and remove it.
Tilt the appliance forward carefully to allow the water to flow out.
Refit the filter and screw it in clockwise as far as it will go.
Refit the plinth.
Before using the washing machine again:
Pour approx.1 litre of water into the detergent drawer
to check that the filter is
inserted properly and securely.
Plug in the appliance once again.
.
.
.
.
.
.
.
.
TROUBLESHOOTING GUIDE
enables faults to be detected in good time and the safety system can then react
appropriately. These faults are frequently so minor that they can be resolved
within a few minutes.
The appliance stops during the programme .
Check whether:
The "
Rinse Hold
" indicator lamp lights up; terminate this option by pressing
Another programme has been selected and the
"Start/Pause"
button not be
button..
The door has been opened and the "
Start/Pause
" button not be pressed.
Close the door and press the
"Start/Pause"
button again.
.
.
.
the Start/Pause button or by choosing and starting the "Drain" programme.
" "
Your washing machine is equipped with various automatic safety functions. This
The washing machine will not start and no indicator lamps are on.
Check whether:
The mains plug is inserted into the socket and the power switched "ON".
T
to test it).
The washing machine will not start.
Check whether:
The door is properly closed (child safety).
The
"Start
/Pause"
button has been pressed.
The Water tap is opened and press the
"
Start/Pause"
button.
.
.
.
.
.
The wall socket is functioning correctly(use a table lamp or similar appliance
press programmepressed.Reselect the desired and the
"
Start/Pause
"
Check if there is excessive foam inside the washing machine. In this case,
select and start the "
Rinse + Spin
" programme. Afterwards, select and start
the desired programme again, using less detergent. If the fault persists,
(See "Fault
.
unplug the appliance and contact our After Sales Service.
Residue from detergent and additives left in the detergent drawer at end of
wash.
Check whether:
The cover grid of the softener chamber and the separator of the main wash
chamber are correctly installed in the detergent dispenser and all parts are
clean (See "Care and Maintenance" ).
Sufficient water is entering. The mesh filters of the water supply could be
blocked (see "
Care and Maintenance
").
The position of the separator in the main wash chamber is adapted to the
use of powder or liquid detergent (see "Detergent and Additives").
.
.
.
Machine vibrates during spin cycle.
Check whether:
The washing machine is level and standing firmly on all four feet.
The transport bolts have been removed. Before using the machine, it is
imperative that the transport bolts are removed.
.
.
Large items in drum could cause drum becomes out of balance. Please be
careful to load the machine balance.
Final spin results are poor.
The washing machine has an imbalance detection and correction system. If
individual heavy items are loaded (e.g. bathrobes), this system may reduce the spin
speed automatically or even interrupt the spin completely if it detects too
great an imbalance even after several spin starts, in order to protect the washing
machine.
If the laundry is still too wet at the end of the cycle, remove some articles of
laundry and repeat the spin cycle.
.
Excessive foam formation may prevent spinning. Use the correct amount of
detergent.
Check that the spin speed selector has not been set to " 0".
If your washing machine has a time display: the programme time initially
lengthened or shortened by a period of time:
This is a normal capacity of the washing machine to adapt to factors that can have
an effect on the wash programme time, e.g.:
Excess foam formation
Load imbalance due to heavy items of laundry
Prolonged heating time due to reduced inlet water temperature
.
.
.
.
.
displayed is
description table").
The washing machine’s safety system has been actived(see Fault description"
.
table").
To Next Page
Loading...
Need help?
General