EasyManuals Logo
Home>HP>Laptop>ENVY x2

HP ENVY x2 User Manual

HP ENVY x2
93 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #80 background imageLoading...
Page #80 background image
Downloading a BIOS update
CAUTION: To reduce the risk of damage to the computer or an unsuccessful installation, download
and install a BIOS update only when the computer is connected to reliable external power using the
AC adapter. Do not download or install a BIOS update while the computer is running on battery power
or connected to an optional power source. During the download and installation, follow these
instructions:
Do not disconnect power from the computer by unplugging the power cord from the AC outlet.
Do not shut down the computer or initiate Sleep.
Do not insert, remove, connect, or disconnect any device, cable, or cord.
1. From the Start screen, select the HP Support Assistant app.
2. Click Updates and tune-ups, and then click Check for HP updates now.
3. Follow the on-screen instructions.
4. At the download area, follow these steps:
a. Identify the most recent BIOS update and compare it to the BIOS version currently installed
on your computer. If the update is more recent than your BIOS, make a note of the date,
name, or other identifier. You may need this information to locate the update later, after it
has been downloaded to your hard drive.
b. Follow the on-screen instructions to download your selection to the hard drive.
Make a note of the path to the location on your hard drive where the BIOS update is
downloaded. You will need to access this path when you are ready to install the update.
NOTE: If you connect your computer to a network, consult the network administrator before
installing any software updates, especially system BIOS updates.
BIOS installation procedures vary. Follow any instructions that are displayed on the screen after the
download is complete. If no instructions are displayed, follow these steps:
1. From the Start screen, type e, and then select File Explorer.
2. Click your hard drive designation. The hard drive designation is typically Local Disk (C:).
3. Using the hard drive path you recorded earlier, open the folder on your hard drive that contains
the update.
4. Double-click the file that has an .exe extension (for example, filename.exe).
The BIOS installation begins.
5. Complete the installation by following the on-screen instructions.
NOTE: After a message on the screen reports a successful installation, you can delete the
downloaded file from your hard drive.
70 Chapter 10 Using Setup Utility (BIOS) and System Diagnostics

Table of Contents

Other manuals for HP ENVY x2

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP ENVY x2 and is the answer not in the manual?

HP ENVY x2 Specifications

General IconGeneral
SteppingC0
Processor cache1 MB
Processor cores2
System bus rate- GT/s
Processor familyIntel AtomĀ®
Processor seriesIntel Atom Z2700 Series
Processor socketFC-MB4760
Processor threads4
Processor codenameCloverview
Processor frequency1.8 GHz
Processor cache typeL2
Processor lithography32 nm
Processor manufacturerIntel
Processor front side bus- MHz
Processor operating modes32-bit
ECC supported by processorNo
Thermal Design Power (TDP)- W
Motherboard chipset-
Internal memory2 GB
Memory clock speed533 MHz
Memory form factorOn-board
Internal memory typeDDR2-SDRAM
Memory layout (slots x size)1 x 2 GB
SSD capacityThe Solid State Drive's storage capacity in Gigabytes.
Storage mediaSSD
Card reader integratedYes
Total storage capacity64 GB
Compatible memory cardsSD
Number of SSDs installed1
Display surfaceMatt
Display diagonal11.6 \
Touch technologyMulti-touch
Touchscreen typeCapacitive
Display resolution1366 x 768 pixels
Native aspect ratio16:9
Discrete graphics card modelNot available
Audio systemBeats Audio
Front camera resolution (numeric)8 MP
Data networkNot supported
Wi-Fi standards802.11b, 802.11g, Wi-Fi 4 (802.11n)
Charging port typeDC-in jack
Headphone connectivity3.5 mm
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity0
Operating system installedWindows 8
Form factorConvertible (Detachable)
Product typeHybrid (2-in-1)
Product colorSilver
Housing materialMetal
Country of originChina
Processor codeSR0Z4
Processor ARK ID70105
Processor package size14 x 14 mm
Battery life (max)7 h
Number of battery cells2+2
AC adapter power20 W
AC adapter frequency50 - 60 Hz
AC adapter input voltage100 - 240 V
Sustainability certificatesRoHS, EPEAT Silver, ENERGY STAR
Weight and Dimensions IconWeight and Dimensions
Depth206 mm
Width303 mm
Height19 mm
Weight1390 g

Related product manuals