HP LP1965 User Manual

ENWW
NOTE You must set the current local time before you reset the time for Sleep Time or
On Time. Note that the time is displayed in a 24–hour clock format. For example, 1:15
p.m. is displayed as 13 hours 15 minutes.
5. Press the Menu button once to enter the adjustment mode for hours.
6. Press the - (Minus) or + (Plus) button to adjust the hour.
7. Press the Menu button again to enter the time for minutes.
8. Press the - (Minus) or + (Plus) button to adjust the minutes.
9. Press the Menu button to lock in the time chosen.
10. After setting the current time, the highlight automatically skips to Set Sleep Time hours. Repeat
steps 6 through 9 to set Sleep Time.
11. If you do not want to set Sleep Time, press the Menu button twice, then select Save and
Return to exit the menu.
12. After setting Sleep Time, the highlight automatically skips to Set On Time hours. Repeat steps
6 through 9 to set On Time.
13. Set the Timer mode to On to activate the Sleep Timer settings.
14. When you are finished, select Save and Return to exit the menu.
The fifth selection, Sleep Now, turns the monitor backlights off immediately and stays in sleep mode
until the next On Time activates or a monitor button is pressed.
HP Display LiteSaver
HP Display LiteSaver is a software application, available on the CD, that increases monitor life and
saves energy. It allows you to place the monitor into its low power sleep mode at predefined times by
shutting down or reducing power to most internal circuits. This helps protect the LCD panel against
image retention. Image retention can occur when the monitor is left on while displaying the same
image for an extended period of time, leaving a shadow of the image on the screen.
Installing the HP Display LiteSaver Software
1. Insert the CD in the computer CD-ROM Drive. The CD menu is displayed.
2. Select Install HP Display LiteSaver Software.
3. After installing the software, click the HP Display LiteSaver icon in the Windows system tray or
right-click the icon and select Configure from the pop-up menu.
4. Select the following options to configure the HP Display LiteSaver features:
Table 4-3 HP Display LiteSaver Configuration Options
Select This Option To Do This
Enable Display LiteSaver Enables the HP Display LiteSaver functions; deselect to disable the HP Display
LiteSaver.
30 Chapter 4 Operating the Monitor

HP LP1965 Specifications

General

Operating temperature (T-T)	5 - 35 °C
Non-operating relative humidity (non-condensing)	5 - 90 %
Pivot angle	0 - 90 °
Plug and Play	Yes
Tilt angle range	-4 - 30 °
Height adjustment	100 mm
Cable lock slot type	Kensington
Panel mounting interface	100 x 100 mm
3D	No
HD type	-
Panel type	TFT
Pixel pitch	0.294 x 0.294 mm
Aspect ratio	4:3
Response time	6 ms
Display surface	Matt
Display diagonal	19 \
Display resolution	1280 x 1024 pixels
Display technology	LCD
Vertical scan range	48 - 76 Hz
Horizontal scan range	24 - 83 kHz
Contrast ratio (typical)	1000:1
Display number of colors	16.78 million colors
Display scanning frequency	Horizontal frequency: 24-83 kHz, Vertical frequency: 48-76 Hz
Display brightness (typical)	300 cd/m²
Supported graphics resolutions	1280 x 1024 (SXGA)
UNSPSC-code	43211902
Audio included	No audio included No audio included at platform level
Rear ports note	4 USB 2.0
Native resolution	SXGA (1280x1024) pixels
Security features	Kensington Lock-ready
Weight (imperial)	15.6 lb lbs
Power requirements	Auto-ranging, 90 to 265 VAC, Internal power supply, 50 to 60 Hz (built-in power supply)
Recommended resolution	Preset VESA Graphic Modes (non-interlaced): 1280 x 1024 @ 60 and 75 Hz, 1024 x 768 @ 60, 70 and 75 Hz, 1152 x 870 @ 75 Hz (Mac), 1152 x 900 @ 76 Hz (Sun), 832 x 624 @ 75 Hz (Mac), 800 x 600 @ 60, 72 and 75 Hz, 720 x 400 @ 70 Hz, 640 x 480 @ 60, 72 and 75
Display resolution at frequency	Preset VESA Graphic Modes (non-interlaced): 1280 x 1024 @ 60 and 75 Hz, 1024 x 768 @ 60, 70 and 75 Hz, 1152 x 870 @ 75 Hz (Mac), 1152 x 900 @ 76 Hz (Sun), 832 x 624 @ 75 Hz (Mac), 800 x 600 @ 60, 72 and 75 Hz, 720 x 400 @ 70 Hz, 640 x 480 @ 60, 72 and 75 Hz
Dimensions (W x D x H) (imperial)	15.9 x 8.78 x 18.79 \
Product dimensions (without stand, imperial)	15.9 x 2.4 x 12.96 \
Product color	Black, Silver
Country of origin	China
AC input voltage	90 - 265 V
AC input frequency	50 - 60 Hz
Power consumption (max)	55 W
Power consumption (standby)	2 W
Power consumption (typical)	35 W
I/O ports	One upstream, four downstream ports (cable included)
USB hub version	2.0
DVI-D ports quantity	0
DVI-I ports quantity	2
USB Type-A downstream ports quantity	3
Cables included	AC, DVI
Interface adapters included	DVI-I female - VGA male

Weight and Dimensions

Depth (with stand)	222.9 mm
Width (with stand)	403.9 mm
Height (with stand)	377.2 mm
Weight (with stand)	7060 g
Depth (without stand)	61 mm
Height (without stand)	329.1 mm
Weight (without stand)	4190 g