EasyManuals Logo
Home>HP>Desktop>ProDesk 490 G2

HP ProDesk 490 G2 User Manual

HP ProDesk 490 G2
160 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #87 background imageLoading...
Page #87 background image
Table 6-2 Computer Setup—Storage (continued)
displayed. Use the arrow keys to select the preferred bootable device and press Enter. The computer then
boots from the selected non-default device for this one time.
Computer Setup—Security
NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration.
Table 6-3 Computer Setup—Security
Option Description
Setup Password Allows you to set and enable a setup (administrator) password.
NOTE: If the setup password is set, it is required to change Computer Setup options, flash the ROM, and
make changes to certain plug and play settings under Windows.
Power-On Password Allows you to set and enable a power-on password. The power-on password prompt appears after a
power cycle or reboot. If the user does not enter the correct power-on password, the unit will not boot.
Password Options
(This selection appears
only if a power-on
password or setup
password is set.)
Allows you to enable/disable:
Lock Legacy Resources (determines whether or not Windows Device Manager is allowed to change
resource settings for serial and parallel ports).
Stringent security (enabling the stringent password disables the ability to reset the password by
moving the jumper on the system board). Default is disabled.
CAUTION: If you enable the stringent security feature and you forget the setup password or the
power-on password, the computer is inaccessible and can no longer be used.
If you lose or forget the password, the system board must be replaced. This scenario is not covered
under warranty.
To prevent the computer from becoming permanently unusable, record your configured setup
password or power-on password in a safe place away from your computer. Without these
passwords, the computer cannot be unlocked.
Setup Browse Mode (appears if a setup password is set) (allows viewing, but not changing, the F10
Setup Options without entering setup password). Default is enabled.
Password prompt on F9 & F12 (requires setup password to use these boot functions). Default is
enabled.
Network Server Mode. Default is disabled.
Device Security Allows you to set Device Available/Device Hidden (default is Device Available) for:
System audio
USB controller (varies by model)
Network controller
NOTE: You must disable AMT before trying to hide the network controller.
Serial port
Parallel port
SATA ports (varies by model)
USB Security Allows you to set Enabled/Disabled (default is Enabled) for:
Front USB Ports
Rear USB Ports
Computer Setup (F10) Utilities 77

Table of Contents

Other manuals for HP ProDesk 490 G2

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP ProDesk 490 G2 and is the answer not in the manual?

HP ProDesk 490 G2 Specifications

General IconGeneral
Tcase72 °C
Bus typeDMI2
SteppingC0
Processor cache3 MB
Processor cores2
System bus rate5 GT/s
Processor familyIntel® Core™ i3
Processor seriesIntel Core i3-4100 Desktop series
Processor socketLGA 1150 (Socket H3)
Processor threads4
Processor codenameHaswell
Number of QPI links0
Processor frequency3.7 GHz
Processor cache typeL3
Processor lithography22 nm
Processor manufacturerIntel
Processor front side bus- MHz
PCI Express slots version3.0
Processor operating modes32-bit, 64-bit
ECC supported by processorYes
PCI Express configurations1x16, 2x8, 1x8+2x4
Thermal Design Power (TDP)54 W
Number of processors installed1
Maximum number of PCI Express lanes16
Memory types supported by processorDDR3-SDRAM, DDR3L-SDRAM
Memory voltage supported by processor1.5 V
Memory clock speeds supported by processor1333, 1600 MHz
Memory bandwidth supported by processor (max)25.6 GB/s
Maximum internal memory supported by processor32 GB
On-board graphics card ID41
Discrete graphics card modelNot available
On-board graphics card modelIntel® HD Graphics 4400
On-board graphics card familyIntel® HD Graphics
Maximum on-board graphics card memory1.74 GB
On-board graphics card OpenGL version4.3
On-board graphics card base frequency350 MHz
On-board graphics card DirectX version11.1
On-board graphics card dynamic frequency (max)1150 MHz
Number of displays supported (on-board graphics)3
Memory slots4x DIMM
Internal memory4 GB
Memory channelsDual-channel
Memory clock speed1600 MHz
Internal memory typeDDR3-SDRAM
Memory layout (slots x size)1 x 4 GB
HDD speed7200 RPM
HDD interfaceSATA
Storage mediaHDD
Optical drive typeDVD±RW
Total storage capacity500 GB
Intel segment taggingEnterprise, Small Business
Operating system installedFreeDOS
Operating system architecture64-bit
Wi-FiNo
Cabling technology10/100/1000Base-T(X)
Ethernet LAN data rates10, 100, 1000 Mbit/s
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Chassis typeMicro Tower
Product colorBlack
Country of originChina
Placement supportedVertical
Product typePC
Motherboard chipsetIntel® H97
Power supply180 W
Power supply input voltage100 - 240 V
Power supply input frequency50 - 60 Hz
Operating temperature (T-T)10 - 35 °C
Operating relative humidity (H-H)10 - 90 %
Sustainability certificatesENERGY STAR
Scalability1S
Processor codeSR1PL
Processor ARK ID77490
Processor package size37.5 x 37.5 mm
Supported instruction setsAVX 2.0, SSE4.1, SSE4.2
Thermal solution specificationPCG 2013C
Intel Secure Key Technology version1.00
Intel Stable Image Platform Program (SIPP) version0.00
Weight and Dimensions IconWeight and Dimensions
Depth358.8 mm
Width165 mm
Height355 mm
Weight6500 g

Related product manuals