Low
and
Medium
security prohibits access to the robotic
lawnmower if the PIN code is unknown.
High
security
also includes a warning that beeps if the correct PIN
code is not entered after a designated time period.
If the wrong PIN code is entered 5 times in succession
the robotic lawnmower is blocked for a time. The
blockage time is extended for every new incorrect
attempt.
Function Low Medium High
Time lock X X X
PIN request X X
Alarm X
3.17.1.1 Time lock
This function means that the robotic lawnmower cannot
be started after 30 days without first entering the correct
PIN code. When the 30 days has passed the robotic
lawnmower will continue to mow as normal, but the
Enter PIN code
message appears the next time STOP is
pressed. Enter the PIN code and press OK.
3.17.1.2 PIN request
This function means that the robotic lawnmower
requests a PIN code if the robotic lawnmower is in
standby and has the security setting
High
. Standby
(flashing indicator lamp) means that the operator must
press the ON/OFF button to make the robotic
lawnmower active again. The correct PIN code must be
entered before it is possible to operate the robotic
lawnmower.
3.17.1.3 Alarm
This function means that an alarm sounds if the PIN
code is not entered within 10 seconds after the STOP
button has been pressed or the robotic lawnmower has
been lifted up for any reason. A ticking noise indicates
that the PIN code must be entered to prevent triggering
the alarm. The alarm can be turned off at any time by
entering the correct PIN code.
3.17.2 Advanced
Advanced
New loop signal
Change PIN code
Duration
3.17.2.1 New loop signal
The loop signal is randomly selected to create a unique
link between the robotic lawnmower and the charging
station. In rare cases, there may be a need to generate
a new signal, for instance if two adjacent installations
have a very similar signal.
1. Place the robotic lawnmower in the charging station.
2. Select
New loop signal
in the menu.
3. Press OK and await confirmation that the loop signal
has been generated. This normally takes about 10
seconds.
3.17.2.2 Change PIN code
1. Enter the current PIN code by using the up/down
arrow keys and press OK.
2. Enter the new PIN code and press OK.
3. Confirm by entering the same code again and press
OK.
When the PIN code is changed, the message
PIN code
changed
appears in the display. Make a note of the new
PIN code on the designated line in Memo. See
Introduction on page 3
.
3.17.2.3 Duration
Duration
Duration of alarm
Duration of time lock
Duration of alarm
When
Alarm
is activated (
High
security) there is also the
possibility to select how long the alarm signal should
last. A figure between 1 and 20 minutes can be
selected.
Duration of time lock
A time lock can be set to decide how many days will
pass before the PIN must be entered before use. 1-90
days can be selected.
3.18 Messages
In this menu the previous fault and information
messages can be found. For some of the messages,
there are tips and advice to help to rectify the fault.
MESSAGES
Fault messages
Info messages
3.18.1 Fault messages
If the robotic lawnmower is disrupted in any way e.g.
gets stuck under a fallen branch a message is shown in
the lawnmower’s display relating to the disruption and
the time it happened.
If the same fault message is repeated several times, this
may indicate that an adjustment to the installation or the
robotic lawnmower is required. See
Fault messages on
page 48
for more information on possible reasons for
each message.
The list contains the latest 50 fault messages sorted by
date with the last incident to occur first on the list.
The date and time when the fault messages are
displayed can be shown by selecting a fault message
and pressing the OK button.
Tips and advice to help you rectify the fault, are also
displayed.
26 - Installation 840 - 001 -
To Next Page
Loading...
Need help?
General
