Ice i24BT User Manual (English)

Other manuals for Ice i24BT

Questions and Answers:

C
Christopher GillAug 17, 2025
What to do if Ice i24BT Scrubber has poor water pick up?
- L
  lfreemanAug 18, 2025
  If your Ice Scrubber isn't picking up water effectively, several factors could be at play. First, check if the recovery tank is full and drain it if necessary. Ensure the drain hose cap is tightened and the float shut-off screen within the recovery tank is free from clogs—clean it if needed. Inspect the squeegee assembly for any blockages and clean them out. Examine the squeegee blades for wear; replace or rotate them as necessary, and adjust the squeegee blade height to ensure correct deflection. Check for loose vacuum hose connections and secure them. Clear any obstructions from the vacuum hose and replace the hose if damaged. Make sure the recovery tank cover is correctly positioned and replace the seal if it's damaged. Lastly, recharge the batteries if the charge is low.
S
Susan GreenAug 20, 2025
How to fix little or no solution flow in Ice i24BT Scrubber?
- R
  rodriguezanthonyAug 20, 2025
  If your Ice Scrubber has little to no solution flow, start by checking the ball valve to ensure it is fully open. Next, verify that the solution flow control knob is properly adjusted and not shut off. Inspect the solution tank filter and solution hose for any clogs; clean the filter or flush the hose as needed. Also, check the solution solenoid valve for clogs, and remove and clean the valve if necessary.
L
Lisa MorganAug 22, 2025
How to improve water pick up with my Ice i24BT?
- S
  Stephen RyanAug 22, 2025
  To improve water pick up with your Ice Scrubber, ensure the recovery tank isn't full by draining it. Check and tighten the drain hose cap if it's loose. Clean the float shut-off screen located in the recovery tank and the squeegee assembly. Replace or rotate worn squeegee blades and adjust the squeegee blade height if the deflection is incorrect. Secure any loose vacuum hose connections, remove debris from a clogged vacuum hose, and replace a damaged vacuum hose. Make sure the recovery tank cover is properly positioned and replace the seal if damaged. Finally, recharge batteries if the charge is low.
M
Mariah PatelAug 26, 2025
Why my Ice i24BT won't turn on?
- B
  Brett CantuAug 26, 2025
  If your Ice Scrubber won't turn on, there are several things to check. First, make sure the control handle bail is pulled. Then, verify that the batteries are adequately charged, and if not, charge them. If the batteries are charged, they may be bad and need replacement. Also, check for loose battery connections and tighten them if necessary. Finally, see if the main control unit circuit breaker has tripped and reset it if it has.
M
Marc WarrenAug 27, 2025
What to do if there is little or no solution flow in Ice Scrubber?
- L
  Luis RiveraAug 27, 2025
  If you're experiencing little to no solution flow in your Ice Scrubber, start by checking the ball valve to ensure it is turned on. Next, adjust the solution flow control knob. If the issue persists, inspect the solution tank filter and solution hose for clogs, cleaning them as necessary. Also, check the solution solenoid valve for clogging and remove and clean it if needed.
X
xclarkAug 30, 2025
How to extend run time of Ice Scrubber?
- G
  Gregory KellyAug 30, 2025
  To extend the run time of your Ice Scrubber, fully recharge the batteries. If the problem continues, the batteries may be defective and need replacement. Also, check the battery charger for faults and repair or replace it if necessary. Lastly, ensure the down pressure lever isn't set for extra scrub head pressure; if it is, lower it.
D
Deanna SmithSep 1, 2025
Why my Ice i24BT Scrubber machine will not operate?
- R
  Robert MarquezSep 2, 2025
  If your Ice Scrubber isn't starting, the control handle bail might not be pulled; ensure you pull it. The batteries may need charging, so charge them fully. Check for loose battery connections and tighten them. The main control unit circuit breaker might have tripped, in which case, reset it. If these steps don't work, the batteries might be bad and require replacement.
C
crivasSep 4, 2025
Why does my Ice Scrubber have a short run time?
- E
  Elizabeth MurphySep 4, 2025
  A short run time for your Ice Scrubber can be due to several reasons. First, ensure the batteries are fully recharged. If the issue persists, the batteries may be defective and need replacement. Check if the down pressure lever is set for extra scrub head pressure and lower it if it is.
M
Mr. William HodgesSep 6, 2025
What to do if my Ice Scrubber has poor water pick up?
- S
  Scott CollinsSep 6, 2025
  If your Ice Scrubber isn't picking up water effectively, several issues could be the cause. First, ensure the recovery tank isn't full by draining it. Check the drain hose cap and tighten it if it's loose. Inspect the float shut-off screen in the recovery tank and clean it if clogged. Also, examine the squeegee assembly for clogs and clean as necessary. Inspect the squeegee blades, if they are worn, replace or rotate them. Adjust squeegee blade height if the deflection is incorrect. Make sure that the vacuum hose connections are secure, and remove any debris clogging the vacuum hose. If the vacuum hose is damaged, replace it. Properly position the recovery tank cover and replace the seal if it's damaged. Lastly, recharge batteries if the battery charge is low.
W
whitney57Sep 9, 2025
What to do if Ice Scrubber has short run time?
- N
  Natasha HaleSep 9, 2025
  If your Ice Scrubber isn't running for very long, the following could be the reason. Fully recharge the batteries if they have a low charge. If the batteries are defective, replace them. If the batteries need maintenance, see BATTERY MAINTENANCE. Lower the down pressure lever if it is set for extra scrub head pressure.