Ice RS26+ User Manual

8 ICE RS26+ / RS32+
OPERATOR MANUAL
MOUNTING THE SQUEEGEE ASSEMBLY
1. Turn o󰀨 the 1-Step switch and raise the
Squeegee assembly o󰀨 the oor.
2. Mount the squeegee assembly to the squeegee
pivot bracket. make sure the knobs are
completely seated into the slots before securing
knobs.
3. Connect the Vacuum hose (Machine
components, #42) to the squeegee assembly.
Loop the hose by using the hose clip provided.
4. Check the squeegee blades for proper
adjustment by adjusting the Squeegee adjusting
knob (Machine components, #44).
FILLING THE SOLUTION TANK
The machine is equipped with a Hose ll port
(Machine components, #3)at the side of the
machine, and a bucket ll-port located under the
recovery tank.
NOTE: Before accessing the bucket ll-port
make sure that the recovery tank is empty.
When lling the solution tank with a bucket,
make sure that the bucket is clean. Do not use
the same bucket for lling and draining the
machine.
AUTO-FILL HOSE PORT(OPTION)
The machine have a optional Auto-ll hose port
(Machine components, #2), you can ll the Solution
tank by using lling hose equipped with Quick
connectors.
1. Connect the Quick connector of the lling hose
to the Auto-ll port and connect the another end
to the water supply connector.
2. Turn the water supply on, the water ow will
automatically shut o󰀨 when solution tank is full,
and then turn the water supply o󰀨.
3. Disconnect the Quick connector from the water
supply end rst, and then disconnect the Filling
hose from machineand store in proper location.
WARNING: Do not put any ammable
materials into solution tank. this can cause an
explosion or a re.
FILLING THE DETERGENT BOTTLE
The machine is equipped with a 4 liters Detergent
bottle under the Recovery tank. You can ll the
Detergent bottle by openning the Deterent bottle
cabin door (Machine components, #25), and
removing the detergent bottle cap.
The ratio of water and detergent is 0~5%, you
can adjust this ratio via pressing the Detergent
adjusting button (Machine components, #33).
NOTE: Only use recommended cleaning
chemicals. Contact your janitorial supply
distributor for recommendations on
properchemicals.
WARNING: Do not operate machine
unless you have read and understand this
manual.
PRE-OPERATION CHECKS
1. Check the tank cover seals for damage.
2. Drain the recovery tank, check the vacuum fan
inlet lter, clean them if necessary.
3. Check the vacuum hose for debris or blockage.
4. Check the squeegees for damage, wear and for
deection adjustment.
5. Check whether Pad/Brush is installed properly .
6. Check the brakes and steering for proper
operation.
OPERATION THE MACHINE
1. Sit on the Operator seat, adjusting the seat
to comfortable place by pushing the Seat
adjustment handle (Machine components, #18).
NOTE: The machine will not travel unless the
operator is sitting in the operator seat.
2. Turn on the machine.
Check the Touch screen (machine components,
#15) , if the machine have fault there will have
a Fault icon display and blinking (Machine
components, #39), please Do Not operation the
machine unless the faults have been eliminated
(please see FAULT CODES AND ELIMINATE
section).
3. Select the proper working mode by pressing
the Work mode select button (Machine
components, #32). The machine have 3 Modes
of ECO, HEAVY Duty and User custom.
NOTE: To energy saving, recommend to
using the ECO mode as possible.
For the User custom mode, you can select
the preferred settings by pressing the Solution
ow adjusting button (Machine components,
#30), Detergent adjusting button (Machine
components, #33), and the Brush pressure
MACHINE OPERATION

Ice RS26+ Specifications

General

Brand	Ice
Model	RS26+
Category	Scrubber
Language	English