Kärcher B 80 User Manual

- 5
ATTENTION
Risk of damage to the floor covering. Do
not operate the appliance on the spot.
 Turn the program selection switch to
the desired cleaning program.
 The appliance controls the lowering
and raising of the cleaning head auto-
matically, depending on the selected
programme mode. The brush motor
also runs and stops automatically.
Note:
The brush motor comes to a halt when the
machine stops and when there is overload.
 The appliance controls the lowering
and raising of the suction bar automati-
cally, depending on the selected pro-
gramme mode.
Note:
For cleaning tiled floors, adjust the straight
suction bar in such a way that cleaning is not
done at an angle of 90 degrees to the joints.
The inclined position and the inclination of
the suction bar can be adjusted to achieve
better suction results (see "Adjusting the
suction bar").
If the wastewater reservoir is full, the float-
er will close the suction opening and the suc-
tion turbine will run at a higher speed. If this is
the case, shut the vacuum off and drive to
empty the wastewater reservoir.
 Close the regulatory button for setting
the water quantity.
 Release driving lever.
 Set the program selection switch to suc-
tion or vacuuming.
 Briefly drive forward and suck of the re-
maining water.
 Remove the Intelligent Key.
 Charge battery, if required.
몇 WARNING
Please observe the local provisions regard-
ing the wastewater treatment.
 Take the water discharge hose from the
support and lower above a suited col-
lection device.
 Crush or bend the dosing equipment.
 Open the lid of the dosing equipment.
 Drain off the dirt water - regulate the
water quantity by pressing or bending.
 Rinse the waste water tank with clean
water or with the rinsing system for the
waste water tank (option).
 Loosen the lid for emptying the fresh
water - do not remove it fully. Drain wa-
ter.
 To rinse the fresh water reservoir, re-
move the cover completely and remove
the fresh water filter.
 Plug in the Intelligent Key.
 Select the desired function by turning
the Info button.
The different functions are described in the
following.
In this menu item, the authorisations for the
yellow Intelligent Keys are released.
 Press the info button while "Key menu
>>“ is displayed.
 Remove the grey Intelligent Key and in-
sert the yellow Intelligent Key to be pro-
grammed.
 Select the desired menu item to be
modified by turning the Info button.
 Press Info button.
 Adjust the menu item by turning the Info
button.
 Confirm the setting by pressing the
menu item.
 Select the next menu item to be modi-
fied by turning the Info button.
 To save the authorisations, retrieve the
menu "Save settings" by turning the info
button and pressing it.
 To exit, retrieve the menu "Exit menu"
by turning the info button and pressing
it.
Parameters that are adjusted with the grey
Intelligent Key, are kept until another set-
ting is selected.
 Turn the program selection switch to
the desired cleaning program.
 Turn the info button until "Cleaning App
>>“ is displayed.
 Press the info button - the first adjusta-
ble parameter is displayed.
 Press Info button - the set value blinks.
 Set the desired value by turning the info
button.
 Confirm the changed setting by press-
ing the Info button or wait till the set val-
ue is automatically accepted after 10
seconds.
 Select the next parameter by turning
the Info button.
 After all desired parameters have been
modified, turn the info button until "Exit
menu" is displayed.
 Press the info button - you will exit the
menu.
 Press Info button - the set value blinks.
 Set the desired language by turning the
info button.
 Confirm the changed setting by press-
ing the Info button or wait till the set val-
ue is automatically accepted after 10
seconds.
Adjust the trailing time of the brushes.
 Same adjustment as "Set language".
 Turn the info button until the function
"Battery menu" is displayed.
 Press the info button - select the charg-
ing marker line according to the built-in
batteries.
Note: Setting the charging marker line
should be discussed with Kärcher cus-
tomer service. This applies especially if
the battery is not listed in the menu.
 Confirm the changed setting by press-
ing the Info button or wait till the set val-
ue is automatically accepted after 10
seconds.
Recreate the basic settings.
 DANGER
Risk of injury! When loading or unloading
the machine, it may only be operated on
gradients up to the maximum value (see
"Technical Specifications"). Drive slowly.
몇 CAUTION
Risk of personal injury or damage! Mind the
weight of the appliance during transport.
 Remove the brush to avoid damage to
the brushes.
 Activate parking brake.
 When transporting in vehicles, secure
the appliance according to the guide-
lines from slipping and tipping over.
몇 CAUTION
Risk of personal injury or damage! Consid-
er the weight of the appliance when storing
it.
This appliance must only be stored in inte-
rior rooms.
Cleaning
Lower the cleaning head
Lower the vacuum bar
Shutting Down the Appliance
Drain off dirt water
Drain off clean water
Grey Intelligent Key
Key menu >>
Cleaning App >>
Setting the language
Brush trailing
Setting the charging marker line
LOAD DEFAULT
Transport
Storage
18 EN

Kärcher B 80 Specifications

General

Brand	Kärcher
Model	B 80
Category	Ultrasonic Jewelry Cleaner
Language	English