EasyManuals Logo
Home>Kohler>Plumbing Product>REVIVAL Series

Kohler REVIVAL Series User Manual

Kohler REVIVAL Series
8 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #2 background imageLoading...
Page #2 background image
Kohler Co., Kohler, WI
2
113341-2-
BB
ROUGHING-IN DIMENSIONS – CONTINUED
X = Distance from centerline of spout inlet to front of spout
base plus 1/2” (1.3cm).
Y = Distance between valve centerlines may vary
depending on your installation requirements.
* Dimension allows for ±1/4” (6mm) handle adjustment
during handle trim installation.
Diameter of hole in deck for spout = 1-1/8” (2.9cm) Max.
Diameter of hole in deck for valve = 1-1/2” (3.8cm) Max.
Thin deck/bath rim installations require additional support
under deck/bath rim. Use 1/2” exterior grade plywood.
For installations on a rough (unfinished) deck to be
covered later with tile, the tile thickness must not exceed
1-1/4” (3.2cm).
X
1/8” (3mm) MIN. - 2-1/8”
(5.4cm) MAX. BATH RIM
THICKNESS
Y
1-13/16” (4.6cm)
5-5/8”
(14.3cm)
X
7/8” D.
1/2” (1.3cm) MIN. - 2-1/8”
(5.4cm) MAX. DECK
THICKNESS
5/8” O.D. TUBING (1/2” NOM.)
5/8” I.D. (1/2” NOM.)
1-5/16” D.
1-1/8” D.
Y
X
7/8” D.
1/2” (1.3cm) MIN. - 2-1/8” (5.4cm)
MAX. ROUGH DECK THICKNESS
5/8” O.D. TUBING (1/2” NOM.)
5/8” I.D. (1/2” NOM.)
1-5/16” D.
1-1/8” D.
1-1/4” (3.2cm) MAX.
TILE THICKNESS
FINISHED DECK- AND BATH-MOUNT ROUGHING-IN
ROUGH DECK PLUS FINISHED DECK (TILE) ROUGHING-IN
*1-1/4” (3.2cm)
Fig. #2
4-5/8”
(11.7cm)
2. INSTALLATION
PREPARATION
For installations with 8” (20.3cm) centers using copper
tubing (1/2” nominal, 5/8” O.D.), cut tubing to the lengths
as follows:
2-pieces: 2-7/8” (7.3cm) long
1-piece: 2-3/8” (6cm) long (for finished deck or bath rim
installation only).
For non-8” (20.3cm) center installations, adjust tubing
lengths as necessary.
INSTALL SPOUT SUPPLY TUBE
Slide brass washer from bottom of spout supply tube over
threads until washer reaches supply tube shoulder.
Insert spout supply tube through mounting hole from top
of deck/bath rim. Ensure flat portion of washer faces
forward. Spout supply tube will be suspended by washer.
Slide plate (oriented with tabs toward deck) and washer
onto spout supply tube from bottom and thread on
mounting nut. Tighten nut.
Secure plate to deck or wooden support with two wood
screws.
NOTE: Leave protective sleeve on spout supply tube un-
til spout installation.
Fig. #3
Supply Tube Shoulder
Brass Washer
Nut
Spout Supply Tube
Washer
Wood Screw
Plate
Wood Screw

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Kohler REVIVAL Series and is the answer not in the manual?

Kohler REVIVAL Series Specifications

General IconGeneral
BrandKohler
ModelREVIVAL Series
CategoryPlumbing Product
LanguageEnglish

Related product manuals