Lennox DVR5-CMNS User Manual

Firestop
Spacer
20 6" (521 mm)
_DST5-HTK Termination Siding
Exterior Surface
Vent
Section
Min.
to
Base
of
Appliance
2196
4"
oreihow
—_Cennestors
(Straight
out
the
i
back
Standard
(51
10
165
mm)
Venting)
Note: Centerline of Vent Piping is NOT the Same
as the Centerline of the Framed Opening.
Figure 13
To install the _DST5-HTK apply a liberal bead of
_Mill-Pac Black (700°) high temperature seal-
ant
at the inner mounting flange for sealing
purposes. Orient the housing with surface
marked “top” upward. Visually align at the
opening and carefully insert to engage over
both inner and outer connector tubes. Slide
inward until the housing bottoms at the fin-
ished exterior wall. The horizontal termination
must not be recessed into the exierior wall or
siding iInanyway. Secure with 6d nails at holes
in upper and lower flanges (Figure 12).
Note: Apply appropriate sealant to the outer
edges of the _DST5-HTK housing.
Install the vinyl wall shield onto the termination
in accordance with the directions provided with
the termination.
The _DOV-HTK-1 termination installs in exactly
ihe same way as the _DST5-HTK termination.
Orient the _DV-HTK-1 with the louvered wall
shield upwards.
Step 6. Installing the Optional Remote Wall
Switch ~The standard _DVR5 millivolt system
comes from the factory wired as shown in
Figure 14. Select a convenient location for the
remote wall switch and connect the wiring to
the appliance {Figure 15).
CAUTION: DO NOT CONNECT THE OPTIONAL
REMOTE SWITCH TO A 120¥ POWER SUP-
PLY.
vi Maximam
_DVR5 Hiillivolt Series
Standard Wiring Diagram
if any of the original wire as supplied must be replaced, it
must be replaced with Type AWM 105°C - 18 GA. wire.
Door Switch
®
From Thermacouple
* For Wall Switeh Attachment Only.
Figure 14
_DVA5 Millivoit Series
Optional Wiring Diagram
f any of the original wire as supplied must be replaced, it
Must be replaced with Type AWM 105°C - 18 GA. wire.
Door Switch
As
=
=
A =
Thermopile |r
(@)
‘Optional ON/OFF
Rocker Switch @
O-O-
From Thermocouple
* For Wall Switch Attachment Only.
Figure 15
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Note: The optional rocker switch is mounted to
the appliance and wired in the same way as the
remote wall switch.
Step 7. Fleld Wiring Electronic Appliances —
Regardless of whether an optional forced air
blower kit (Figure 76) is to be installed now or
sometime in the fuiure, the appliance must be
connected to the main power supply. To install,
Toute a 3-wire 120V 60Hz power supply to the
appliance junction box (located in the lower left
side of the appliance) and ground. Also, at this
time you may wish to locate and install an
optional low voltage (24V) wail switch (Figure
17) in the desired location, connect the low
voltage wire to this switch and/or install ther-
mal snap switch in series. Refer to the instal-
lation instructions provided with the forced air
kit. :
_DVA5 Electronic Series
1. Sf any of the original wire as supplied must be replaced,
it must be replaced with Type AWM 105°C ~ 18 GA. wire.
2. 120V, 60Hz— Less than’3 amps,
Gas Valve pot OPT. .AacEssonY
i
common assemsyy | UH
BRS
TGNITER
rit
—a—
a
(=C
Opposite Side
Junction Box
Ap —___] 2a 4
eB
BK .
Loa
f
ae
[eel
R
Door
SWITCH
Factory Wired 9 -vsteerrree Field Wired
* For ON/OFF Wall Switch Attachment Only,
Figure 16
CAUTION: BO NOT CONNECT THE OPTIONAL
REMOTE SWITCH TO A 120V POWER SUP-
PLY.
Note: The optional rocker switch is mounted to
the appliance and wired in the same way as the
remote wall switch (Figure 17).
f i r e - p a r t s . c o m

Lennox DVR5-CMNS Specifications

General

Brand	Lennox
Model	DVR5-CMNS
Category	Fireplace Accessories
Language	English