To Next Page

To Previous Page

SWR • SWC • SWD Swing Gate Operator Installation Guide - 11 - 227965 Revision X22 8-11-2011

Operator Accessory Connections

3-BUTTON STATION

KEYSWITCH

FIRE ACCESS SWITCH

SINGLE-CHANNEL RADIO RECEIVER

WIRELESS GATE EDGE SENSOR

MGT

TRANSMITTER

PHOTOEYE FOR REVERSE

PHOTOEYE FOR OPEN OBSTRUCTION

TELEPHONE ENTRY

KEYPAD

EXTERNAL POWER

SOLENOID LOCK

MAGLOCK

WARNING STROBE OR AUDIBLE SOUNDER

GATE EDGE SENSOR FOR REVERSE

CHANNEL #1

OPEN/CLOSE

TWO-CHANNEL RADIO RECEIVER

PHOTOEYE FOR CLOSE OBSTRUCTION

Figure 13. Operator Accessory Connections

Default Chapter2
- Table of Contents2
Pre-Installation Information3
- Before You Begin3
- Always Check the Gate's Action3
- Gate Operator Classiﬁ Cations3
- Approved Obstruction Detection Devices3
Safety Information and Warnings3
- Regulatory Warnings3
Wiring Speciﬁ Cations4
- AC Power Wiring4
- DC Control and Accessory Wiring4
Mounting Pad Installation5
- Mounting Pad Speciﬁ Cations5
Operator Preparation6
- Vent Plug Installation6
Gate Arm Installation6
- Setting Left or Right Hand Conﬁ Guration6
- Gate Plate Installation6
- Choosing Good Harmonics7
- Installing the Gate Arm on the Operator7
- Setting the Arm Lengths7
Operator Setup8
- Controller Access8
- AC Power Connection8
- Earth Ground8
- Limit Cam Rough Adjustment9
- Torque Limiter Adjustment9
- Limit Cam Fine Adjustment9
Controller Features10
Indicator Descriptions11
Terminal Descriptions12
Operator Accessory Connections13
Basic Controller Programming14
- Programming Overview14
- Entering Programming Mode14
- Exiting Programming Mode14
- Programming Keystrokes14
- Left or Right Hand Operation14
- Dual Gate Enable14
- Auto Close Timer14
- Run Alarm and Pre-Start Alarm15
- Maximum Open Direction Current Setting15
- Maximum Close Direction Current Setting15
Advanced Controller Programming16
- Entering Advanced Programming Mode16
- Maximum Run Time16
- Single Button Input Setup16
- Stagger Mode16
- Stagger Delay Time17
- Auxiliary Relay Mode17
- Reverse Delay Time17
- Constant Pressure Mode17
- Shadow Loop Open Prevention18
- Low Power Mode18
- Power Failure Mode18
- Soft Start/Stop Duration19
- Reset Cycle Count19
- Maintenance Alert Trigger19
- MID-Travel Stop Position20
- Anti-Tailgate Enable20
- Motor Type Selection20
- Radio Enable21
- Antenna Installation21
- Radio Transmitter Learn21
- Radio Transmitter Delete21
- MGT Obstacle Transmitter Learn21
- MGT Obstacle Transmitter Delete21
- Reset Controller to Factory Defaults21
Loop Layout Illustration22
Safety Edge Layout Illustration23
Photoeye Installation Illustration24
Dual Gate Installations25
Gate Operation25
- Open Button25
- Close Button25
- Stop Button25
- Single Input25
- Fire Department Input25
- Open Input25
- Open Obstruction25
- Close Obstruction25
Operation Indications26
- Power-Up Display26
- Idle Condition26
- Last Gate Position/Condition26
- Pre-Start Delay26
- Reverse Delay26
- Run Timer26
Error Indications26
- Entrapment26
- COMM LINK Connection Failure26
Troubleshooting27
- Contacting Technical Support27
- Operator Fails to Start27
- Motor Operates, but Gate Does Not Move27
- Motor Sounds Like It Is Working Harder than Normal27
- Limit Switch Getting out of Time27
- Gate Stopping Part Way Open or Closed (but no Visible Obstruction)27
- Gate Staying Open with Automatic System27
- How to Order Replacement Parts27
Model SWR Exploded View28
Model SWC Exploded View29
Model SWD Exploded View30
SWR, SWC, SWD Gate Arm Assembly Exploded View31
Model SWD Maintenance32
- Battery Maintenance32
- DC Motor Brush Replacement32
Preventative Maintenance33
- General33
- Lubrication33
- 6-Month Preventative Maintenance33
FCC Notice33
Gate Operator Installation Checklist34

Brand	Linear
Model	SWC
Category	Gate Opener
Language	English

Linear SWC User Manual

Table of Contents

Questions and Answers:

Linear SWC Specifications

Related product manuals