Mercury Security Corporation, © 2008 BR20 Doc. 10107-0024 rev. 1.03 10/2008 Page 4
Information subject to change without notice.
11. Reader Verification:
The reader performs a self-test when power is first applied to the unit. If power-on test is successfully completed, the
reader will turn on both LEDs for approximately 1 second and sound the buzzer for 1 short beep. Then the reader is
ready for normal operation.
If further verification of the reader hardware is needed, the reader may be temporarily set to format 3. With this format
selected, the reader will read and verify standard ANSI track 2 encoded card. If no read error is detected, the green
LED will flash. Otherwise, the red LED will flash and the buzzer will sound two short beeps to indicate an error. The
LED input can be used to verify the LED function; and the buzzer input for the buzzer function. The reader will echo
a key press with a brief flash of both LEDs and a short beep of the buzzer. Reset to the required format for normal
operation after test.
12. Maintenance:
The reader is designed to provide continuous service with minimal routine maintenance. However, contaminants (such
as magnetic oxides from badges and dirt) tend to accumulate on the read head. Without regular cleaning, these
contaminants will shorten the read head life and increase the probability of card read error. A maintenance schedule
should be developed base on the card reader environment (dirty or clean) and the usage frequency (light traffic or heavy
traffic). Extreme case may require daily cleaning.
Head cleaning may be done by using a disposable, pre-saturated magnetic head cleaning card. These cards are readily
obtainable from a number of sources (e.g. Clean Team Co., www.cleanteam.com, 800-888-8830; KIC Products,
www.kicproducts.com, 207-514-7030; System ID, www.systemid.com, 888-648-4452).
The reader exterior surface is covered with high strength polymer and polyester membrane. It may be cleaned with
a soft cloth and mild detergent if required.
13. Specifications:
The reader is for use in low voltage, class 2 circuits only.
Power: Voltage 5Volt Model: 5.8 Vdc (4.9 to 6.4 Vdc)
12Volt Model: 12 Vdc (10.2 to 13.8 Vdc)
Current 50mA (25mA typical.)
Data output: Clock/data or data 1/0 pair
Timing clock/data: period 1mS
setup/hold time 400uS, clock pulse width 200uS typical
data 1/0: period, 1mS for Wiegand data, 1mS for mag stripe data
pulse width 50uS typical
LED input: 1-wire mode input not driven: LEDs OFF
input > 3.5Vdc: Red LED ON
input < 0.8Vdc: Green LED ON
2-wire mode input < 0.8Vdc: Red LED ON
Buzzer/LED: 1-wire mode input not driven or > 3.5Vdc: buzzer OFF
input < 0.8Vdc: buzzer ON
2-wire mode input < 0.8Vdc: Green LED ON
Mechanical: Dimension 2.59" (66mm) W x 1.30" (33mm) H x 5.50" (140mm) L
Weight 11.3 oz. (320 g) nominal
Material Case, Die cast aluminum, gray powder coat standard.
Mounting, stainless steel
Wall plate, 18 CRS, gray powder coat standard
Card: 75 bpi, ANSI X4.16, Track 2 standard, Speed 3 to 50 ips
Read Head: 1,000,000 passes typical.
Distance: 500' (152m) with 18 AWG wires.
Environmental: Temperature -55 to +85 degrees C, storage
-40 to +75 degrees C, operating
Humidity 0-100% RHNC
To Next Page
Loading...
Need help?
General