Meyer Sound PSM-2 User Manual

2
According to ISO/IEC Guide and EN 45014
The product herewith complies with the require-
ments of the Low Voltage Directive 73/23/EEC and
the EMC Directive 89/336/EEC.
declares that the product:The Manufacturer:
Product Name: PSM-2
Product Options: All
Name: Meyer Sound Laboratories
Address: 2832 San Pablo Avenue
Berkeley, California 94702-2204, USA
conforms to the following Product Specifications:
Safety: EN 60065: 1994
EMC: EN 55022: 1987 - Class A
IEC 801-2: 1984 - 8 kV
IEC 801-3: 1984 - 3 V/m
IEC 801-4: 1984 - 0.5 kV Signal Lines,
Meyer Sound Laboratories, Inc.
2832 San Pablo Avenue
Berkeley, California 94702
Telephone:510 - 486 - 1166
FAX: 510 - 486 - 8356
E-mail: techsupport@meyersound.com
http://www.meyersound.com
Made by Meyer Sound, Berkeley, CA, USA
European Office:
Meyer Sound Germany
GmbH
Carl Zeiss Strasse 13
56751 Polch, Germany
UU
LL
CC
UU
LL
®®
LISTED
3K59
COMMERCIAL
AUDIO SYSTEM
Meyer Sound Germany
Gmbh
Carl Zeiss Strasse 13
56751 Polch, Germany
Telephone: 49.2654.9600.58
FAX: 49.2654.9600.59
Declaration of Conformity
Contact Information
Office of Quality Manager
Berkeley, California USA
October 1, 1995
1.0 kV Power Lines
Shock: 30 g 11 msec half-sine
on each of 6 sides
Vibration: 10 – 55 Hz (0.010 m
peak-to-peak excursion)
Operating temperature:0° C to +45° C
Non-operating temp: < –40° C or > +75° C
Humidity: to 95% at 35°C
Operating altitude: to 4600 m (15,000 ft)
Nonoperating altitude: to 6300 m (25,000 ft)
Environmental Specifications for
Meyer Sound Electronics Products
!
Pour indiquer les risques
résultant de tensions
dangereuses
Zu die gefahren von
gefährliche spanning zeigen
Important operating
instructions
Pour indequer important
instructions
Zu wichtige betriebs-
anweisung und unter-
haltsanweisung zeigen
Frame or chassis
Masse, châssis
Rahmen oder chassis
Protective earth ground
Terre de protection
Die schutzerde
Para indicar azares provengo
de peligroso voltajes
Para indicar importante
funcionar y mantenimiento
instrucciones
Armadura o chassis Tierra proteccionista
These symbols indicate important safety or operating features in this booklet and on the chassis.
Dangerous voltages:
risk of electric shock
Symbols Used

Meyer Sound PSM-2 Specifications

Acoustical

frequency response	± 4 dB 50 Hz – 18 kHz
phase response	± 90° 200 Hz – 16 kHz
maximum SPL	139 dB peak at 1 m

Transducers

low frequency driver	12” diameter MS-12 cone driver
high frequency driver	4” diaphragm MS-2001CQ horn driver
acoustical crossover point	800 Hz

Amplifiers

burst capability	1240 Watts (620 Watts per channel)
THD, IM, TIM	< .02 %
type	Complementary power MOSFET output stages class AB/H

AC Power

automatic voltage selection	85 – 134 V / 165 – 264 V; 50 Hz / 60 Hz
max continuous RMS current	115 V: 8 A 230 V: 4 A 100 V: 10 A
max peak current during burst	115 V: 22 Apk 230 V: 11 Apk 100 V: 25 Apk

Physical

dimensions	24” W x 18” H x 14 5/8” D
weight	90 lb (41 kg)
shipping weight	103 lb (47 kg)