To Next Page

To Previous Page

Paper recommendations > 33

> Envelopes should be loaded flap down, face up with the top edge to the left and

short edge into the printer.

> Load Transparencies face up and top edge into the printer.

> For heavyweight paper or cardstock open the rear output cover to collect the

printed output. This will give the paper a nearly straight path through the

machine, avoiding paper jams and damage to the paper.

3. B420, B430: If required, set the media size and orientation in the media menu

using the control panel, then issue the print command.

B410: If required, set the media size and orientation in the Printer Menu Setup tool,

then issue the print command.

APER

FEED

SIZE

AND

MEDIA

SETTING

The process used to fuse (fix) the printed image to the paper involves a mixture of pressure

and heat. Too much heat will cause lightweight paper to crease or curl and corrugations in

transparencies. Too little heat will cause the image not to fuse fully into heavyweight paper.

B410

AND

B410

You can change the media type as follows:

1. Start the Printer Menu Setup tool.

2. Click Media Menu.

3. Click on the paper tray being used. Adjust the media type to the required setting

and, if necessary, the paper size to the size of the paper being used.

4. Click on the Setup tab and click Apply the changed settings, then OK to set the

printer to the new media type.

NOTE

Do not select Duplex printing on envelopes.

CAUTION!

Damage to the printer may occur if the incorrect paper setting is

used when printing on a different media.

NOTE

> You can also set the media type in your printer driver. However, the

printer driver settings will override the settings on the control panel or

Printer Menu Setup Tool.

> Remember to reset the printer for normal paper after printing on a

different media.

NOTE

Although media properties can be set in the printer driver for particular jobs,

when filling a tray with media it is recommended that you manually set the

printer to match the media as described here.

Downloaded From ManualsPrinter.com Manuals

Other manuals for Oki B430DN

Specifications4 pages

Questions and Answers:

Need help?

Do you have a question about the Oki B430DN and is the answer not in the manual?

Oki B430DN Specifications

General

Color	No
Duplex printing	Yes
Print technology	Laser
Maximum resolution	1200 x 1200 DPI
Time to first page (black, normal)	5.5 s
Print speed (black, normal quality, A4/US Letter)	28 ppm
Internal memory	64 MB
Processor model	PowerPC405
Sound power level (standby)	30 dB
Sound pressure level (printing)	53 dB
Total input capacity	250 sheets
Total output capacity	150 sheets
Envelopes sizes	C5, C6, DL
Media weight (tray 1)	60 - 120gsm
Paper tray media types	Envelopes
Non-ISO print media sizes	Executive (184 x 267mm), Legal (media size), Letter (media size), Statement (140 x 216mm)
ISO A-series sizes (A0...A9)	A4, A5, A6
JIS B-series sizes (B0...B9)	B5
Maximum ISO A-series paper size	A4
Supported network protocols (IPv4)	TCP/IP:-ARP, IPv4/v6, TCPv4, ICMPv4/v6, UDPv4/v6, LPR, FTP, TELNET, HTTP(IPP), BOOTP, DHCP, AutoIP, SNMP, DNS, uPnP, Bonjour, WINS, Windows Rally(WSD-Print, LLTD), SLP, JetDirect protocols. Netware 3.x, 4.x, 5.x, and 6 with full NDS and NDPS support:- QServer over IP and IPX, R-Printer, N-Printer, NCP, SPX, IPX, SAP, RIP, Ethertalk:- ELAP, AARP, DDP, AEP, NBP, ZIP, RTMP, ATP, PAP, NetBEUI: SMB, NetBIOS
Power requirements	230 VAC, 50 - 60Hz
Networking features	10/100BaseTX
Compatible operating systems	Windows 2000 / XP / XP x64 / Server 2003 / Server 2003 x64 / Vista (32-bit) / Vista (64-bit) / UNIX / Linux; Mac OS X PowerPC 10.2.8 + / OS X Intel 10.4.4 +
Display	LCD
Maximum duty cycle	70000 pages per month
Operating temperature (T-T)	10 - 32 °C
Operating relative humidity (H-H)	20 - 80 %