setting
6
0.6 to 6 6 to 60
24
2.4 to 24 24 to 240
60
6 to 60 60 to 600
Ratings
Rated
supply voltage (see note 1)
100 to 240 V
AC (50/60 Hz)/100 to 125 VDC, 24 to 48 V
AC (50/60 Hz)/12 to 48 VDC (24 to
48 V
AC/VDC for H3CR-A8E) (see note 2)
Operating voltage range
85% to 1
10% of rated supply voltage (90% to 1
10% at 12 VDC)
Power reset
Minimum power-opening time: 0.1 s
Input
No-voltage Input
ON impedance:
1 kΩ
max.
ON residual voltage: 1 V max.
OFF impedance:
100 k
Ω
min.
V
oltage Input
Max. permissible capacitance between inputs lines (terminals 6 and 7): 1,200 pF
Load connectable in parallel with inputs (terminals 6 and 7).
• 100
to 240 V
AC/100 to 125 VDC
High (logic) level:
85 to 264 V
AC/85 to 137.5 VDC
Low (logic) level:
0 to 10 V
AC/0 to 10 VDC
•
24 to 48 V
AC/12 to 48 VDC
High (logic) level:
20.4 to 52.8 V
AC/10.8 to 52.8 VDC
Low (logic) level:
0 to 2.4 V
AC/0 to 1.2 VDC
Power consumption
H3CR-A/-A8
• 100
to 240 V
AC/100 to 125 VDC
(When at 240 V
AC, 60 Hz)
Relay ON: approx. 2.1 V
A (1.6 W)
Relay OFF: approx. 1.3 V
A (1.1 W)
•
24 to 48 V
AC/12 to 48 VDC
(When at 24 VDC)
Relay ON: approx. 0.8 W
Relay OFF: approx. 0.2 W
H3CR-AP
(see note 3)
• 100
to 240 V
AC/100 to 125 VDC
(When at 240 V
AC, 60 Hz)
Relay ON: approx. 2.5 V
A (2.2 W)
Relay OFF: approx. 1.8 V
A (1.7 W)
•
24 to 48 V
AC/12 to 48 VDC
(When at 24 VDC)
Relay ON: approx. 0.9 W
Relay OFF: approx. 0.3 W
H3CR-A8E
• 100
to 240 V
AC/100 to 125 VDC
(When at 240 V
AC, 60 Hz)
Relay ON/OFF: approx. 2 V
A (0.9 W)
•
24 to 48 V
AC/VDC
(When at 24 VDC)
Relay ON/OFF: approx. 0.9 W
H3CR-AS/-A8S
•
24 to 48 V
AC/12 to 48 VDC
(When at 24 VDC)
Output ON: 0.3 W Output OFF: 0.2 W
Control outputs T
ime limit contacts:
5 A at 250 V
AC/30 VDC, resistive load (cosφ
= 1)
T
ransistor output:
Open collector (NPN/PNP), 100 mA max. at 30 VDC max.,
residual voltage: 2 V max.
Instantaneous contact:
5 A at 250 V
AC, resistive load (cosφ
= 1)
Note: 1.
DC ripple rate: 20% max. if the power supply incorporates a single-phase, full-wave rectifier
.
2. Each
24-to-48-V
AC/12-to-48-VDC model causes an inrush current
of approximately 0.85 A. Pay careful attention when attempting
to
turn ON power to such a model with non-contact output from a device such as a sensor
.
3. The
values are for when the terminals 2 and 7 and terminals 10 and 6 are short-circuited, and include the consumption
current of the
input circuit.
To Next Page
Loading...
Need help?
General
