Omron H3DE-S1 User Manual

H3DEH3DE
Specifications
J GENERAL
Item H3DE-M2 H3DE-M1 H3DE-S2 H3DE-S1
Operating mode A: ON-delay (Signal or Power)
B: Repeat-cycle OFF start (Signal or Power)
B2: Repeat-cycle ON start (Signal or Power)
C: Signal ON-/OFF-delay
D: Signal OFF-delay
E: Interval (Signal or Power)
G: Signal ON-/OFF-delay
J: One-shot (Signal or Power)
A: ON-delay
B2: Repeat-cycle ON start
E: Interval
J: One-shot
Terminal block Clamps two 2.5 mm
2
max. bar terminals without sleeves.
Terminal screw tightening
torque
0.98 N S m max. {approx. 10 kgf S cm max.}
Input type Voltage input ---
Output type Relay: DPDT Relay: SPDT Relay: DPDT Relay: SPDT
Mounting method DIN track mounting (See Note.)
Attachment Nameplate
Approved standards UL508, CSA 22.2 No.14
Conforms to EN61812-1, IEC60664-1 (VDE0110) 4 kV/2, VDE0106/P100
Output category according to IEC60947-5-1 (AC-13; 250 V 5A/AC-15; 250 V 3 A/DC-13; 30 V 0.1 A)
Note: Can be mounted to 35-mm DIN track with a plate thickness of 1 to 2.5 mm.
J TIME RANGES
Time scale display T ime unit display
seconds min hrs 10 h
x0.1 0.1to1.2s 0.1to1.2min 0.1to1.2h 1to12h
x1 1to12s 1to12min 1to12h 10 to 120 h
Note: When the main dial is set to “0” for all settings, the output will operate instantaneously.
J RATINGS
Rated supply voltage
(See Notes 1 and 2.)
24 to 230 VAC/DC (50/60 Hz)
12 VDC (H3DE-M2 model only)
Operating voltage range 85% to 110% of rated supply voltage
Power reset Minimum power-off time: 0.1 s
Reset voltage 2.4 VAC/DC max.
Power
consumption
(
S
N
t
3
)
H3DE-M1 AC: approx. 4.3 VA (2.2 W) at 230 VAC
DC: approx. 0.7 W at 24 VDC
p
(See Note 3.)
H3DE-M2 AC: approx. 4.8 VA (2.4 W) at 230 VAC
DC: approx. 1.0 W at 24 VDC
H3DE-S1 AC: approx. 2.7 VA (1.6 W) at 230 VAC
DC: approx. 0.7 W at 24 VDC
H3DE-S2 AC: approx. 3.2 VA (1.9 W) at 230 VAC
DC: approx. 1.0 W at 24 VDC
Voltage input Max. permissible capacitance between input lines (terminals B1 and A2) : 2000 pF
Load connectable in parallel with inputs (terminals B1 and A2)
H-level: 20.4 to 253 VAC/DC
L-level: 0 to 2.4 VAC/DC
Control output Contact output: 5 A at 250 V AC with resistive load (cosφ = 1); 5 A at 30 VDC with resistive
load (cosφ =1)
Ambient temperature Operating: --10°Cto55°C (14 to 131°F) with no icing
Storage: --25°Cto65°C(--13°F to 149°F) with no icing
Ambient humidity Operating: 35% to 85%
Note: 1. DC ripple rate: 20% max.
2. Since an inrush current of 0.25 A will occur when using the power supply voltage at 24 VDC, pay careful attention when turning
on or off the power supply to the Timer with a solid-state output such as a sensor.
3. The power consumption is for mode A (ON-delay) after the Timer counts the time-up time and for the AC input at 50 Hz. The
power consumption of the H3DE-Mj includes the input circuit with the B1 and A1 terminals short-circuited.

Omron H3DE-S1 Specifications

General

Brand	Omron
Model	H3DE-S1
Category	Timer
Language	English