Onkyo CP-1057F User Manual

racking)
2 motdtestbemscalelnglonly]
%
. 4
Now, slowly rotate the counterweight in the direction of
the arrow (the scale ring will also rotate) until the 1.7 gram
indication of the ring is allgned with the index line on the
tonearm.
After setting the appropriate amount of tracking force,
set the anti-skating knob to the same value. If this
is forgotten, the stylus may skid over the surface of the
record during record play.
Connections
Connect the output cord from the CP-1057F to the
PHONO terminals of your audio amplifier as shown
below. Connect the power cord to the socket on the
rear panel of the amplifier or the wall socket.
If the unit you have purchased is equipped with a cartridge,
the cartridge is an MC type. Therefore, the amplifier
cartridge selector should be set to the MC position before
using this unit for the first time.
Power cord
GND
PHONO
Do not reverse left and right output cords.
Playing a Record
Always wipe records with a good cloth to remove dust
and other particles before placing the stylus in the
starting
grooves.
Also
confirm
that
no
dust
is
clinging
to the stylus. A dirty record and stylus can cause
unpleasant static during record play.
The
CP-1057F
is
a
fully
automatic
turntable.
However,
manual
and
auto-repeat
operation
are
also
possible.
Be
sure
the
unit
has
been
set
properly
before
beginning
record
play.
In
particular,
check
the
tracking
force
setting
and
connections
regularly.
Fully Automatic Operation
1. Place a record on the turntable mat {1} and set the
Speed Selector [22] to the correct speed for the record
about to be played. The speed switches between 33 and
45 each time the Speed Selector [22] is pressed and
the corresponding indicator lights.
2. Set the Record Size Selector 21] to the correct
setting for the record about to be played.
The record size setting switches between 30 cm
and 17 cm each time the Record Size Selector
is pressed and the corresponding indicator lights.
3. Press the Play/Reject Button [16] ; the turntable
platter 3] will begin to rotate, and the tonearm 13}
will automatically move over to the record, lower
into the starting grooves and begin record play.
4. When the end of the record is reached, the tonearm
13] will automatically return to the arm rest 12 and
the turntable platter {3} will stop rotating.
5. To interrupt record play before the end is reached,
depress the Play/Reject Button [16] . The tonearm
13, will immediately return to the arm rest (12) and
the turntable platter!3\ will stop rotating.
6. Do not touch or forcibly move the tonearm during
this time as it will damage the automatic mechanism.
Manual Operation
Fully
automatic
operation
can
only
be
used
to
play
a
record
from
the
beginning.
To
begin
record
play
from
another
location,
it
is
necessary
to
operate
the
CP-1057F
manually.
Press
the
Cue
Button
{17
to
the
up
position
to
raise
the
tonearm
13!
off
the
arm
rest.
Now
move
the
tonearm
over
the
record
until
the
stylus
is
directly
over
the
section
to
be
played:
the
turntable
will
automatically
begin
rotating.
Depress
the
Cue
Button
again
to
lower
the
tonearm
onto
the
record
surface
and
begin
record
play.
The
tonearm
will
automatically
return
to
the
arm
rest
when
the
end
of
the
record
is
reached
or
the
Play/
Reject
Button
{16)
is
depressed.
Repeat Function
To operate the repeat function, simply depress the
Repeat
Button
19].
The
REPEAT
LED
indicator
will
light
up
and
the
record
will
be
played
again
and
again.
The repeat function is cancelled by depressing the
Play/Reject Button [16] to stop record play immediately,
or by depressing the Repeat Button [19] once more, in
which
case
the
record
will
be
played
to
its
end.
In
either
case,
the
REPEAT
LED
indicator
will
turn
off.

Onkyo CP-1057F Specifications

General

Brand	Onkyo
Model	CP-1057F
Category	Turntable
Language	English