39
English
04 Advanced Features
¦ Listening through a Receiver
You can listen to sound through a receiver (i.e Home Theater) instead of the TV Speaker.
1. Select Receiver and set to On.
2. Press the EXIT button to exit.
✎
If your receiver supports audio only, it may not appear in the device list.
✎
The receiver will work when you have properly connected the optical in jack of the receiver to the DIGITAL AUDIO
OUT (OPTICAL) jack of the TV.
✎
When the receiver (i.e Home Theater) is set to On, you can hear sound output from the TV’s Optical jack. When
the TV is displaying a DTV (air) signal, the TV will send out 5.1 channel sound to the receiver. When the source is a
digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from
the receiver.
✎
NOTE
x
You can only control Anynet+ devices using the TV remote control, not the buttons on the TV.
x
The TV remote control may not work under certain conditions. If this occurs, reselect the Anynet+ device.
x
The Anynet+ functions do not operate with other manufacturers’ products.
¦ Troubleshooting for Anynet+
Problem Possible Solution
Anynet+ does not work. Ř Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.
Ř Only one receiver (home theater) can be connected.
Ř Check if the Anynet+ device power cord is properly connected.
Ř Check the Anynet+ device’s Video/Audio/HDMI cable connections.
Ř Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
Ř Check whether the TV remote control is in TV mode.
Ř Check whether the remote control is Anynet+ compatible.
Ř Anynet+ doesn’t work in certain situations. (Searching channels, operating Media Play or Plug & Play (initial
setup), etc.)
Ř When connecting or removing the HDMI cable, please make sure to search devices again or turn your TV off
and on again.
Ř Check if the Anynet+ Function of Anynet+ device is set on.
I want to start Anynet+. Ř Check if the Anynet+ device is properly connected to the TV and check if the Anynet+ (HDMI-CEC) is set to
On in the Anynet+ Setup menu.
Ř Press the TOOLS button to display the Anynet+ menu and select a menu you want.
I want to exit Anynet+. Ř Select V
iew TV in the Anynet+ menu.
Ř Press the SOURCE button on the TV remote control and select a non- Anynet+ device.
Ř Pr
ess
z
, PRE-CH, and FAV.CH to change the TV mode. (Note that the channel button operates
only when a tuner-embedded Anynet+ device is not connected.)
The message “Connecting to
Anynet+ device...” appears on the
screen.
Ř You cannot use the remote control when you are configuring Anynet+ or switching to a view mode.
Ř Use the remote control when the Anynet+ setting or switching to view mode is complete.
The Anynet+ device does not play. Ř You cannot use the play function when Plug & Play (initial setup) is in progress.
The connected device is not
displayed.
Ř Check whether or not the device supports Anynet+ functions.
Ř Check whether or not the HDMI cable is properly connected.
Ř Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
Ř Search Anynet+ devices again.
Ř You can connect an Anynet+ device using the HDMI cable only. Some HDMI cables may not support Anynet+
functions.
Ř If connection is terminated because there has been a power interruption or the HDMI cable has been
disconnected, please repeat the device scan.
The TV Program cannot be
recorded.
Ř Check whether the antenna jack on the recording device is properly connected.
The TV sound is not output
through the receiver.
Ř Connect the optical cable between TV and the receiver.
To Next Page
Loading...
Need help?
General