EasyManuals Logo
Home>Sanyo>Cassette Player>MCD-UB575M

Sanyo MCD-UB575M User Manual

Sanyo MCD-UB575M
25 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #17 background imageLoading...
Page #17 background image
16
CD PLAY
Use compact discs bearing the symbol shown
in Fig. 6. In addition to conventional 12cm CDs,
this unit can be used to play 8cm CDs without
an adapter.
1. Set the FUNCTION switch to CD/USB.
2. Press the CD OPEN button to open the CD
compartment lid. “OP” appears on the dis-
paly.
3. Place the disc with the label facing up on the
turntable (Fig. 7). (Place only one disc at a
time.)
4. Press the CD compartment lid (PUSH TO
CLOSE portion) to close it.
The total number of tracks on the disc appears
on the display.
5. Press the PLAY/PAUSE i button.
The current track number appears. Play starts
from the first track.
- To start play from the desired track, select
the track by using the f/FILE- or FILE+/
e button, then press the PLAY/PAUSE
i button.
Note:
If no disc is loaded or the disc is located with the
label facing down, “no” appears. If these occur,
load the disc correctly or replace the damaged
disc.
Notes on handling compact discs
- Do not expose the disc to direct sunlight,
high humidity or high temperature for ex-
tended periods of time.
- Discs should be returned to their cases after
use.
- Do not apply paper or write anything on the
disc surface.
- Handle the disc by its edge. Do not touch
the playing surface (glossy side).
- Fingerprints and dust should be carefully
wiped off the playing surface of the disc
with a soft cloth.
Wipe in a straight motion from the center to
the outside of the disc.
- Never use chemicals such as record clean-
ing sprays, antistatic sprays or uids, ben-
zene or thinner to clean compact discs.
Temporarily stopping play
Press the PLAY/PAUSE i button, k ap-
pears on the display. To resume play, press the
button again.
Skip play
Example:
To skip to track 6 while track 3 is playing, press
the FILE+/e button repeatedly until 06 ap-
pears on the display. To skip back to track 3
while track 6 is playing, press the f/FILE-
button repeatedly until “03” appears.
Search (forward/reverse)
If the FILE+/e or f/FILE- button is pressed
during play, the player will search at high speed
in the forward or reverse direction while the
button is being pressed. When the button is re-
leased, normal play will continue.
6. Press the STOP n button to end disc play
back.
When the last track has been played, the player
stops automatically.
7. To turn the CD player off, set the FUNCTION
switch to TAPE/OFF.
Note:
Do not open the CD compartment during CD play.
Always press the STOP n button and wait for
the disc to stop rotating before opening the CD
compartment.
This unit can play back the CD-R/RW as well.
However, some CD-R/RW can not be played back
depending on the recording conditions.
575PAEn.indd 16 2006.12.5 11:04:15 AM

Other manuals for Sanyo MCD-UB575M

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Sanyo MCD-UB575M and is the answer not in the manual?

Sanyo MCD-UB575M Specifications

CD Player IconCD Player
channels2-Channel stereo
sampling frequency44.1 kHz
laser output0.6 mW
wave length790 nm
Radio IconRadio
FM reception frequency87.5 - 108 MHz
AM reception frequency526.5 - 1606.5 kHz
Cassette Deck IconCassette Deck
track system4-track, 2-channel stereo
tape speed4.75 cm/sec.
frequency response80 - 12, 000 Hz
General Specifications IconGeneral Specifications
output power (DC)2 W/ch
output power (AC)1.5 W/ch
speakers10 cm x 2, 8 ohms
dimensions410 (W) x 167 (H) x 286 (D) mm
weightApprox. 2.8 kg
power source (AC)110 V, 60 Hz
power source (DC)12V, 8 “D/HP2/R20” batteries

Related product manuals