Sanyo plc-xu4001 User Manual

45
Setting
31RWH
 'XULQJ,QSXWVHDUFK is in progress, If the MENU
button or the ON/STAND-BY button is pressed,
,QSXWVHDUFK will stop. If the COMPUTER 1/2 or
VIDEO or COMPONENT or S-VIDEO or HDMI
button is pressed, ,QSXWVHDUFK will stop and go
back to the button's input signal.
 ,QSXWVHDUFK, $XWR3&DGM and $XWRNH\VWRQH
can not be set 2II at the same time.
 $XWRNH\VWRQH corrects vertical distortion only,
not correct horizontal distortion.
 7KH$XWRNH\VWRQHIXQFWLRQFDQQRWZRUNZKHQ
the Ceiling feature is set On in the Screen menu
(pp. 35, 43).
 3HUIHFWFRUUHFWLRQRIWKHLPDJHGLVWRUWLRQFDQQRW
be ensured with the Auto setup function. If the
distortion is not corrected properly by pressing the
AUTO SETUP or the AUTO SET button, adjust
manually by pressing the KEYSTONE button on
the remote control or selecting .H\VWRQH in the
Setting menu (pp. 35, 43).
 )LQHV\QF, 7RWDOGRWV, +RUL]RQWDO and Vertical of
some computers cannot be fully adjusted with the
Auto PC Adjustment function. When the image is
not provided properly with this operation, manual
adjustments are required (pp. 30-31).
$XWRVHWXS
,QSXWVHDUFK
This function detects the input signal
automatically. When a signal is found, the search
will stop. Use the Point Ÿź buttons to select
one of the following options.
2II ....... Input search does not work.
On 1..... Input search works under the following
situation.
–When pressing the AUTO SET
button on the remote control.
–When pressing the AUTO SETUP
button on the top control.
On 2......Input search works under the following
situation.
–When turning on the projector by
pressing the ON/STAND-BY button
on the top control or the remote
control.
–When pressing the AUTO SET button
on the remote control.
–When pressing the AUTO SETUP
button on the top control.
–When the current input signal is cut
off.*
* If the No show or Freeze function is active,
cancel it to activate the Input search. It is
also unavailable when On-Screen menu is
displayed.
$XWR3&DGM
On...............Enables Auto PC Adjustment when
pressing the AUTO SET button
on the remote control or the AUTO
SETUP button on the top control.
2II...............Disables Auto PC Adjustment.
$XWRNH\VWRQH
$XWR
.......... Always works and corrects
keystone distortion according to the
projector's tilt.
Manual......Works only when pressing the
AUTO SET button on the remote
control or the AUTO SETUP button
on the top control.
2II.............Disables Auto Keystone.
$XWRVHWXS
31RWH
  :KLOH,QSXWVHDUFK is set to On 1 or On 2, the
status of Input and Lamp are displayed every time
the signal is switched.
  2QO\WKHODVWVHOHFWHGLQSXWVRXUFHFDQEH
detected.
This function enables Input search, Auto PC
adj. and Auto Keystone adjustment by pressing
the AUTO SETUP button on the top control or
the AUTO SET button on the remote control.
Settings for those functions can be altered as
follows:

Sanyo plc-xu4001 Specifications

General

Brand	Sanyo
Model	plc-xu4001
Category	Projector
Language	English