www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
46
|
GB
Measured sound pressure level L
pA
93 dB(A)
Uncertainty K
pA
3 dB
Guaranteed sound power level L
wA
114 dB(A)
Measured sound power level L
wA
108,7 dB(A)
Uncertainty K
wA
3 dB
Vibration Front handle 10 m/s²
Vibration Rear handle 9 m/s²
Uncertainty 1,5 m/s²
7. Before starting up
m CAUTION!: Do not start the motor until the
saw has been fully assembled and checked.
m CAUTION!: When handling the chain always
wear protective gloves.
Assembling the bar, and the chain (Fig.3-6)
Open the box and assemble the bar and chain as fol-
lows:
1. Press the front hand guard back (Fig.14/Pos.3a)
so that the chain brake is disabled.
2. Loosen the two nuts (B) and remove the cover
(17) and spacer (A).
3. Mounting the stopper claw (Fig.3)
Insert the stopper claw (19) into the recesses of
the housing (see Fig. 3) and secure with the 2 x-
ing screws (19a). Use the tool supplied with the
assembly tools (10).
4. Slide the chain around the sprocket, next slide
the saw chain around the bar. Pay attention to the
installation direction of the chain. (Fig.4-5)
5. Insert the chain tensioning screw (Z) into the low-
er hole of the chain bar (Y). (Fig.4)
6. Install the cover (17) and tighten the nuts (B) by
hand.
Installation direction of the chain (shown Fig.5)
Tensioning the chain (Fig.6-8)
1. Hold the front part tight with your hand.
2. Adjust the chain tension using the tension screw
(C) so that the chain rests entirely on the bar, but
not under great tension.
3. Tighten the mounting nut (B) for the bar with the
key (12-15 Nm).
4. Check with your hand that the chain runs smooth-
ly on the rail and has the proper voltage.
5. Where necessary, set up the chain tension.
If the chain has to be re-tensioned
6. Technical data
Machine without guide bar
L x W x H
375 x 182 x 190 mm
Weight without guide bar
and saw chain and empty
tank
5.1 kg
Weight with guide bar and
saw chain and empty tank
7.0 kg
Cutting Length 47 cm
Guide bar length 508 mm
Automatic chain oiling yes
Saw chain Oil
Special Saw chain
oil
Saw chain oil tank capacity 260 cm
3
Saw chain division 0.325″/ 8,255 mm
Drive link thickness 0,057″ / 1.47 mm
Saw chain type Oregon 21BPX078X
Number of teeths drive
sprocket
7
Tooth pitch of drive sprocket 0.325″
Chain brake yes
Guide bar type
Oregon
208PXBK095
Saw chain speed max. 21,2 m/s
Motor
1 cylinder 2 stroke
air cooled
Engine capacity 53 cm³
Maximum motor capacity 2 kW
Idle speed 3100±300 min
-1
Maximum speed with cut-
ting attachment
11000 min
-1
Fuel tank capacity 550 cm
3
Fuel type mix 40:1
Keep the noise emissions and vibrations to a
minimum.
Wear hearing protection.
The eects of noise can cause a loss of hearing.
• Only use appliances which are in perfect working
order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance o when it is not in use.
• Wear protective gloves.
To Next Page
Loading...
Need help?
General
