Scheppach MIX125 User Manual

6. Installing upper section of drum Fig.8
Place rubber ring on the lower section. Place the
upper section of drum on it.
Caution! The pasted arrows mark the exact direc-
tion of the upper or lower section of the drum.
Align the upper section of the drum and install
it on the lower section with 6 M8x16 cross-head
screws with washers and tighten. Lock mixer (9)
with 2 M8x20 cross-head screws and 2 lock-
washers to the lower section of the drum with 2
washers, 2 lockwashers and 2 M8 nuts. Insert
one rubber washer each between mixer and
drum.
7. Installing lockwasher Fig.9
Install lockwasher (13) with 2 M8x25 hexagon
bolts, 2 washers, 2 lockwashers on the swivel
axis and tighten.
8. Installing swivel wheel. Fig.10
Insert the spring with the washer on the top into
the sleeve on the tipping wheel. Slide the wheel
over the larger diameter shaft until the holes in
the braket line up with the hole drilled. Insert a
M10X65 hex bolt with a at washer and screw on
a nut with a at washer from the other side.
Screw the nut up against the bracket rmly, but
not so tightly so as to prevent the wheel from piv-
oting about the bolt. Tighten the M10X30 socket
head cap screw on the sleeve to adjust the spring
tension.
Note: The wheel must be allowed to pivot about
the bolt so that the lugs on the bracket can be
engaged or disengaged from the slots in the lock-
ing plate.
9. Installing motor casing. Fig.11
Place the motor casing on the retaining plate, se-
cure with 4 M8 safety nuts and at washers.
Operation
Operate the concrete mixer only if no parts
(e.g., safety covers) are missing or defective,
and the connecting cable is not damaged.
Set up:
• Place the concrete mixer horizontally on even,
rm ground.
• Do not place it on the connecting cable!
• Route the connecting cable in a manner, such
that it cannot be kinked, crushed or damaged
in some other way.
Note:
It should be possible to swivel the drum to
the right and left. There must be sufcient
space for a wheelbarrow under the drum, so
that it can be emptied.
Activation:
• Plug the device into the socket Activation on
“I” (green button) / Deactivation on “0” (red
button)
Moving the drum (Fig. 12):
• To move the drum, pull back the hand wheel so
that the drum can be moved.
• When the drum is in the desired position, lock
the hand wheel again.
Filling
• Before lling the drum, ensure that the opening
is aligned in such a way that the mixture cannot
fall out of the drum. (Fig. 13)
• Put the mixture in when the drum is rotating
(do not overll the drum)
Caution! Risk of moving parts
Emptying
• Swivel the drum in the downward direction to
empty it
• Ensure that there is an adequate container un-
der the drum (e.g., wheelbarrow).
• Ensure that no mixture falls on the ground
Transport
Caution!
Pull the power plug out, every time, before trans-
porting the machine.
1. Set the lling opening downwards.
2. During transportation by motor vehicle, re-
move the screws and fold the stands.
3. Lock the mixer with a strap to prevent displace-
ment
4. Do not lift the concrete mixer with the help of
a crane
Maintenance
Caution!
While working with the concrete mixer or per-
forming repairs on it, please do the following:
Switch off the concrete mixer, wait for the drum
to come to a standstill and pull out the power
plug.
Repairs on the concrete mixer should be per-
formed only by authorised technicians.
Perform visual inspection before each use of the
concrete mixer.
All safety parts must be installed.
Defective connecting cables should not be used.
Service information
Please note that the following parts of this prod-
uct are subject to normal or natural wear and that
the following parts are therefore also required for
use as consumables.
Wear parts*: V-belts
* Not necessarily included in the scope of deliv-
ery!
Cleaning
Caution! Switch off the machine, wait for the
drum to come to a standstill and pull out the
power plug.
Clean the drum with water after each use of the
concrete mixer.
Remove cement and mortar residues. Do not tap
motor casing and drum with a shovel or any other
hard object, as these can be damaged.
Checking/re- adjusting belt tension
Caution! Switch off the machine, wait for the
drum to come to a standstill and pull out the
power plug.
• Remove the cover of the motor casing, check
the belt tension (on pressing the belt with the
nger, it should yield by approx. 5mm.)
• Belts are wear and tear parts that must be
replaced after a certain period. If necessary,
detach the screws on the motor, replace the
belt, adjust the correct tension and tighten the
screws again.
• Reinstall the motor cover.
Troubleshooting
Fault Possible cause Remedy
Motor switches off Motor is overloaded Let motor cool down
Motor runs, drum does not move V-belt skids through Replace V-belt
Switch off the concrete mixer if such faults occur, pull out the power plug and get the fault rectied by an authorised professional company
17
DGB

Scheppach MIX125 Specifications

General

Brand	Scheppach
Model	MIX125
Category	Mixer
Language	English