20.5 Temperature limits
WARNING
■ The battery is not protected against all ambi‐
ent conditions. If the battery is exposed to cer‐
tain environmental conditions, it may catch fire
or explode. This may result in serious injury to
people and damage to property.
►
Do not charge the battery below -20°C or
above +50°C.
► Do not use the brushcutter, battery or
charger below - 20 °C or above + 50 °C.
► Do not store the brushcutter, battery or
charger below -20°C or above +70°C.
20.6 Recommended temperature
ranges
For optimum performance of the brushcutter,
battery and charger, observe the following tem‐
perature ranges:
–
Charging: 5°C to 40°C
–
Use: - 10 °C to + 40 °C
–
Storage: - 20 °C to + 50 °C
If the battery is charged, used or stored outside
the recommended temperature ranges, perform‐
ance may be reduced.
If the battery is wet or moist, allow the battery to
dry for at least 48 h between 15°C and 50°C and
with less than 70% humidity. Higher humidity
may extend the drying time.
20.7 Sound Values and Vibration
Values
The K value for the sound pressure level is
2 dB(A). The K value for the sound power level is
2 dB(A). The K-value for vibration level is 2 m/s².
STIHL recommends wearing hearing protection.
–
Sound pressure level L
pA
measured in accord‐
ance with IEC 62841-4-4: 76 dB(A)
–
Sound power level L
wA
measured in accord‐
ance with IEC 62841-4-4: 89 dB(A)
–
Vibration value a
hv
measured in accordance
with IEC 62841-4-4:
–
Control handle: 4.8 m/s².
–
Loop handle: 3.6 m/s²
The vibration levels indicated were measured
according to a standardized test method and can
be used as a basis for comparing electric power
tools. The vibration levels actually occurring may
vary from the values indicated, depending on the
type of application. The vibration levels indicated
can be used for an initial estimate of the vibration
load. The actual vibration load has to be estima‐
ted. The times can be taken into account in the
estimate when the electric power tool is switched
off and also when it is switched on but running
without any load.
For information on compliance with the Physical
Agents (Vibration) Directive 2002/44/EC, see
www.stihl.com/vib.
20.8 REACH
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
For information on compliance with the REACH
regulation see www.stihl.com/reach.
21 Combinations of Cutting
Attachments and Deflec‐
tors
21.1 STIHL brushcutter FSA 30.0
The following mowing heads may be mounted
with the deflector:
–
PolyCut 3-2 mowing head
–
with blades (Ø 230 mm)
–
with 1.6 mm diameter “round, quiet” mowing
line (Ø 250 mm)
–
AutoCut C 3-2 mowing head (Ø 250 mm)
–
with 1.6 mm diameter “round, quiet” mowing
line
Using a mowing head with mowing lines may
shorten the battery runtime.
22 Spare Parts and Accesso‐
ries
22.1 Spare parts and accessories
These symbols indicate original STIHL
spare parts and original STIHL acces‐
sories.
STIHL recommends the use of original STIHL
spare parts and accessories.
Despite ongoing market observation, STIHL is
unable to judge the reliability, safety and suitabil‐
ity of other manufacturers' spare parts and
accessories; accordingly, STIHL cannot warrant
for the use of those parts.
Original STIHL spare parts and original STIHL
accessories are available from STIHL dealers.
21 Combinations of Cutting Attachments and Deflectors English
0458-039-0101-A 21
To Next Page
Loading...
Need help?
General
