41
I25 I24 I23 I22 I21 I20 tr th sl se pt pl no nl it hu hr fr fi es en el de da cz
Attach squeegee
FIll the Flex tank
Dosage:
Please use the recommended TASKI chemical products only.
Dosing examples (The concentration is product dependent)
Beginning work
Option 1
Option 2
Option 1 and 2
If you keep driving despite this warning:
• the brush unit and the squeegee will be raised from the floor after approx. 5
minutes.
• the suction unit will switch off after approx. 10 seconds (red display lights up
continuously).
• you still have approx. 10 minutes to run to the nearest mains socket before
the running drive switches off.
• Switch the machine off.
• Lay the squeegee under the squeegee holder.
• Position the squeegee so that the squegee
holder is under the towing strap.
• Press the mounting pedal down until the
squeegee locks in, and then release pressure.
The squeegee lifts up from the floor when the
mounting tool is released.
• Plug the two suction hoses into the squeegee.
• Switch the machine off using the keyswitch and remove the key.
• Reach into the opening between the tank cover
and the tank (with the palm of your hand
upwards). Pull the locking bracket forward and
open the tank cover.
• Check that the sieve and the Flex tank are installed.
• Remove the dosing cup from the Flex tank.
Caution:
Maximum permissible water temperature 60 °C/140 °F.
• Fill the Flex tank with water.
The upper red mark indicates the maximum
permissible filling level.
The lower red mark indicates the half-full level.
Caution:
When handling chemical products, always wera gloves,
protective goggles and the corresponding (protective) work
clothing! (in accordance with the information propvided by the
detergent manufacturer)
Caution:
Using other chemicals (e.g. chemicals containing solvents,
chlorine, hydrochloric acid and hydrofluoric acid) can damage or
destroy the machine.
Instructions on the product’s
packaging
Tank capacity The volume per
tank filling
0.5% 100ml to 10l
water
105l 525ml = 0.525l
1.0% 200ml to 10l
water
105l 1050ml = 1.05l
• Add the measured product to the water in the Flex tank using the dosing
cup.
• Insert the suction filter at the lowest point of the Flex tank.
• Place the dosing aid in the tank and close the tank lid.
By exerting slight pressure onto the front of the lid, you can click it into the
latch.
Caution:
When closing the tank cover, do not hold onto the locking bracket.
You could trap your finger!
Caution:
Always wear non-slip shoes and appropriate work clothing while
working with this machine!
• Always hold the driver's handle with both hands
to ensure safe operation of the machine.
Caution:
Familarise yourself with the machine first by carrying out a few
driving trials in a free area!
• Stand on the platform.
Check that the Emergency Stop button has been released.
• Switch the machine on (Keyswitch to the Start position).
The indicators light up.
• Press the Start/Stop button.
The last cleaning settings used are stored and
will be re-started by pressing the Start/Stop
button.
• Press the brush unit button.
The indicators light up.
• Set the brush pressure with the +/- buttons (min. Level 1/ max. Level 3).
• Press the vacuum button.
The indicators light up.
The suction motor is started and the squeegee
is lowered.
• Press the solution button.
The indicators light up.
• Set the quantity of the cleaning solution using the +/- buttons (min. Level 1/
max. Level 6).
• Hold the driving handle with both hands.
• Set the machine in motion by gently pressing the speed controls.
The tools begin to rotate and the cleaning solution is fed through the centre.
When the last green display on the battery indicator goes out, an audible
signal is given and the red display blinks. Run the machine to the nearest
mains socket or to the battery charger.
Caution:
The manual brake release may only be operated on an even
surface, and a second person must always be present when
pushing the machine.
To Next Page
Loading...
Need help?
General
