EasyManuals Logo
Home>TCL>TV>65C825

TCL 65C825 User Manual

TCL 65C825
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #29 background imageLoading...
Page #29 background image
7
Chapter 2 Getting Started
Switching On
Follow the instructions on this page on how to switch on your TV set
and the remote control before going on to following pages describing
how to use the channel set-up procedure.
1. Insert two AAA batteries in the remote control.
Precautions on using batteries:
- Only use the battery types specied.
- Make sure you use the correct polarity.
- Do not mix new and used batteries.
- Do not use rechargeable batteries.
- Do not expose batteries to excessive heat such as sunshine,
re or the like, throw them in a re, recharge them or try to open
them, as this could cause them to leak or explode.
- Remove the batteries from the remote control if you are not using
it for a long period of time.
- Attention should be drawn to the environmental aspects of battery
disposal.
2. Connect the power cable FIRST to the television, THEN to a mains
socket. (Note: If the power cable is connected to the television,
please only connect the power cable to the mains socket.)
Your TV set should only be connected to an AC supply. It must
not be connected to a DC supply. If the plug is detached from the
cable, do not, under any circumstances, connect it to a mains
socket, as there is a risk of electric shock.
Note: The gures are for representation only, the location of power
socket of the television may differ depending on the model.
3. Connect an outside aerial to the ANTENNA/CABLE IN socket at
the back of the TV set.
The aerial socket (75 OHM - VHF / UHF / cable) can be used for
connecting an external aerial or other equipment tted.
Note: If you want to receive the signal from your cable or cable
box, please connect a coaxial cable to the ANTENNA/CABLE IN
socket at the back of the TV set.
4. When powered on, the TV will be turned on directly or be in
standby mode.
If the power indicator lights up, the TV set is in standby mode.
Press the button on the remote control or on the TV set to turn
on the TV.
Switching Off
To put the TV set into standby mode, press the button on the
remote control. The TV set remains powered up, but with low
energy consumption.
To switch off the TV set, unplug the mains socket from the mains
outlet.
Note: In order to save energy and protect environment, certain models
are designed with a relay switch. It is a normal phenomenon if you
hear the sound of the relay when you turn on or off the TV set.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the TCL 65C825 and is the answer not in the manual?

TCL 65C825 Specifications

General IconGeneral
Screen shapeFlat
Response time9 ms
Display diagonal65 \
Rotating displayNo
Anti-glare screenYes
Display brightness1000 cd/m²
Display technologyQLED
Native aspect ratio16:9
Native refresh rate120 Hz
LED backlighting typeMini LED
Supported video modes2160p
Viewable size diagonal1640 mm
Viewing angle, vertical- °
Contrast ratio (typical)-
Display diagonal (metric)165.1 cm
Supported graphics resolutions3840 x 2160
Motion interpolation technologyPPI (Picture Performance Index) 4200
Dynamic contrast ratio marketing nameMega Contrast
AC input voltage220 - 240 V
AC input frequency50 Hz
Energy efficiency scaleA to G
Power consumption (max)300 W
Power consumption (standby)0.29 W
Audio decodersDolby Atmos, Dolby Digital, Dolby Digital AC4, Dolby TrueHD
RMS rated power60 W
Number of speakers2
Package depth227 mm
Package width1642 mm
Package height1085 mm
Package weight41900 g
Ambient modeIntelligent Picture
Game featuresAuto Low Latency Mode (ALLM), Game Master Pro, Variable Refresh Rate (VRR)
Processor cores4
Audio formats supportedWMA, MP3
Image formats supportedHEIF, JPG, PNG, BMP
Video formats supportedAVI, WMV, MP4, MPG, TS, MKV, WEBM
Picture processing technologyTCL AiPQ 2.0 Engine
High Dynamic Range (HDR) technologyDolby Vision IQ, High Dynamic Range 10+ (HDR10 Plus), High Dynamic Range 10 (HDR10), Hybrid Log-Gamma (HLG)
RF connector typeF, IEC
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Ethernet LAN (RJ-45) ports1
Consumer Electronics Control (CEC)T-link
Common interface Plus (CI+) version1.3
Tuner typeAnalog & digital
Number of tuners1 tuner(s)
Channels quantity- channels
Analog signal format systemNTSC, PAL, SECAM
Digital signal format systemDVB-C, DVB-S2, DVB-T2
Video appsAmazon Prime Video, Netflix, YouTube
Smart modesGame, Movie, Sports
Lifestyle appsGoogle Apps
Operating system version11.0
Operating system installedAndroid
Programming period8 day(s)
Number of OSD languages39
Firmware upgradeable viaNetwork, USB
Wi-Fi standards802.11g, Wi-Fi 4 (802.11n), Wi-Fi 5 (802.11ac), Wi-Fi 6 (802.11ax)
Bluetooth version5.2
Bluetooth profilesA2DP, HID
Color nameBrushed Silver Metal
Product colorSilver
Mercury content0 mg
Panel mounting interface400 x 400 mm
Cables includedAC
Remote control typeRC802NU1
Truck type87 cbm
Pallet width1150 mm
Pallet weight240000 g
Pallet net height1220 mm
Pallet net length1650 mm
Quantity per truck160 pc(s)
Quantity per pallet5 pc(s)
Number of pallets per truck32 pc(s)
Quantity per master (outer) case1 pc(s)
Master (outer) case GTIN (EAN/UPC)5901292515690
Maximum number of stacking cartons3 pc(s)
Doesn't containMercury
Country of originPoland
CertificationCE
Weight and Dimensions IconWeight and Dimensions
Depth (with stand)290 mm
Width (with stand)1446 mm
Height (with stand)904 mm
Weight (with stand)32000 g
Depth (without stand)76 mm
Height (without stand)883 mm
Weight (without stand)31400 g

Related product manuals