EasyManuals Logo
Home>Technics>Headphone>EAH-AZ60

Technics EAH-AZ60 User Manual

Technics EAH-AZ60
37 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #29 background imageLoading...
Page #29 background image
Other
29
Troubleshooting
Before requesting service, make the following checks. If you are in doubt about some of the check points, or if
the remedies indicated do not solve the problem, consult your dealer for instructions.
No sound.
Make sure that the earphones and the Bluetooth
®
device are connected correctly. (l 19)
Check if music is playing on the Bluetooth
®
device.
Make sure that the earphones are turned on and the volume is not set too low.
Pair and connect the Bluetooth
®
device and the earphones again. (l 19)
Check if the Bluetooth
®
compatible device supports “A2DP” profile. For details on profiles, see “Listening to music”
(
l 21). Also refer to the operating manual for the Bluetooth
®
compatible device.
Low volume.
Also raise the volume on the Bluetooth
®
device, not just on the earphones.
Make sure there is no earwax, foreign matter, etc., attached to the earpieces of the earphones.
Remove the earpieces from the main unit (earphones) and refer to “Earphones/Earpieces” (
l 3) to clean them.
Sound from the device is cut off. / Too much noise. / Sound quality is bad.
Sound may be disrupted if signals are blocked. Do not fully cover the earphones with the palm of your hand, etc.
The device may be out of the 10 m communication range. Move the device closer to the earphones.
Remove any obstacle between the earphones and the device.
Switch off any wireless LAN device when not in use.
The device cannot be connected.
You can pair a maximum of 10 Bluetooth
®
devices with the earphones. When you pair a device after the maximum
has been exceeded, previous devices are overwritten. To use overwritten devices again, do the pairing again.
Delete the registration information for this unit from the Bluetooth
®
menu, etc., of the Bluetooth
®
device, then pair
again. (
l 19)
The voice of the person on the other end of the call is small.
Also raise the volume on the Bluetooth
®
device, not just on the earphones.
Cannot make a phone call.
Check if the Bluetooth
®
compatible device supports “HSP” or “HFP” profile. For details on profiles, see “Listening to
music” (
l 21) and “Making a phone call” (l 22). Also refer to the operating manual for the Bluetooth
®
enabled
phone.
Check the audio settings on the Bluetooth
®
compatible telephone, and if the setting does not allow communication
with this unit, change the setting. (
l 19)
The other party finds it hard to hear your voice during a call.
The earphones detect your voice with voice activity detection microphones to enable the other party to hear it. Your
voice cannot be detected if the earpieces are not fitted snugly into your ears. Replace with earpieces that fit snugly
into your ears. (
l 10)
Sound and audio volume
Bluetooth
®
device connection
Phone Calls
eah_az60_az40_pnqp1675za_full_eng_s.book 29 ペー 2021年9月28日 火曜日 午前10時7分

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Technics EAH-AZ60 and is the answer not in the manual?

Technics EAH-AZ60 Specifications

General IconGeneral
Headset typeBinaural
Product typeHeadset
Product colorBlack
Wearing styleIn-ear
Volume controlTouch
Recommended usageCalls/Music
Protection featuresWater resistant
International Protection (IP) codeIPX4
Ear padsYes
Cables includedUSB
Eartips materialSilicone
Charging case typeWired
USB connectorUSB Type-C
Wireless range10 m
Connectivity technologyTrue Wireless Stereo (TWS)
Driver unit8 mm
Ear couplingIntraaural
Microphone typeBuilt-in
Continuous audio playback time7.5 h
Battery life450 min
Weight and Dimensions IconWeight and Dimensions
Depth28 mm
Width23 mm
Height26 mm
Weight7 g
Charging case weight45 g

Related product manuals