Technics Quartz ST-G45A User Manual

™
Zz.
7)
bake
Yn
x
= The indication AM used here includes
e| ; } O ry rese | Nn g S both MW and LW for Model ST-G45AL.
Important! Notes:
1. For automatic presetting in areas where there are less than
16 FM stations, the remaining channels (through channel 16)
will be left empty. The empty channels can be filled by using
manual memory presetting.
2. 1f a new broadcasting station is preset into a channel, the
broadcasting station which was previously entered in that
channel will be automatically erased. Then reset the
memory.
3. For AM _ broadcasts with extremely strong signal
transmissions, the frequency memorized may be slightly off
of the correct frequency. If this occurs, use the manual
control to memorize.
Automatic memory presetting
The FM broadcasting stations and AM broadcasting stations will be automatically preset to “channels” 1 through 16 for FM
and 9 through 16 for AM, respectively.
The FM broadcasting stations, MW broadcasting stations, and LW broadcasting stations will be automatically preset in
“channels” 1 through 16 for FM, 9 through 16 for MW, and 13 through 16 for LW, respectively.
Note: When AM is automatically preset, the FM stations on “channels” 9 through 16 will be replaced by the new AM stations.
This antenna must be
installed to receive AM
broadcasts.
AM loop antenna (included)
With this unit you may preset as many as 16 radio broadcast
stations: FM/AM random presetting. After broadcast stations
have been preset as described below, any desired station can be
quickly and easily selected by simply touching one button.
eke “EM”: for FM broadcasts Before presetting the broadcasting
on” (a— =) “AM”: for AM broadcasts stations, press to select the
appropriate frequency step for
“3 “FM”: for FM broadcasts your locality.
Channel display “MW”: for MW broadcasts (Refer to page 5.)
“LW”: for LW broadcasts
Memory indicator
ST-G45A
we BB Deed ix
Set to the lowest frequency.
Tuning Press the left button to change the frequency
downward, and press the right button to change the
frequency upward.
. “2 @ FM: 87.50 MHz (0.05 MHz step)
~ @ AM: 522 kHz (9 kHz step) or
530 kHz (10 kHz step)
(For Europe, South Africa and Australia)
531 kHz (9 kHz step) or
530 kHz (10 kHz step)
(For Saudi Arabia and others)
e FM: 87.50 MHz (0.05 MHz step)
Press. When the frequency indication
begins to change, release.
The frequency will change upward, and the automatic
presetting will begin with the next broadcasting
station. It will continue to preset the following
consecutive broadcast stations.
© MW:522 kHz (9 kHz step) or Confirm the names (call signs, etc.) of the
530 kHz (10 kHz step) broadcasting stations which are preset to
e LW: 153 kHz (9 kHz step: -2kHz shift) 9 Pl
or 155 kHz (9 kHz step) each channel, and enter them on the file sheet
(page 8).
ak
@ Press the button and hold slightly OTe ‘ha To check the front channels (CH 1~ 8):
(frequency will change continuously). SS) Press momentarily. Frequency stored in the memory
Se & and channel number are
® ci displayed.
@ Release it when approaching the c by stereo oa m ~
above exact frequency, and then FM ef Ly mz ch
press the button again momentarily
(frequency change will stop). ; bs To check the back channels (CH 9~ 16):
[2 Press slightly longer. Frequency stored in the memory
and channel number are
@® Press the button momentarily displayed.
by
(frequency will change each time ® bg
the buttonis pressed), and tune Cihy
to one of the above frequencies.
7397
a (cu wa S|

Technics Quartz ST-G45A Specifications

General

Brand	Technics
Model	Quartz ST-G45A
Category	Tuner
Language	English