Technics SL-MC60 User Manual

Before
use
Precautions
Before using this unit please read these operating instructions care¬
fully. Take special care to follow the warnings indicated on the unit
itself as welt as the safety suggestions listed below.
Afterwards keep them handy for future reference.
Safety
1. Power Source - The unit should be connected to power supply
only of the type described in the operating instructions or as
marked on the unit.
2. Polarization - If the unit is equipped with a polarized AC power
plug (a plug having one blade wider than the other), that plug will fit
into the AC outlet only one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety purpose of
the polarized plug.
3. Power Cord Protection - AC power supply cords should be
routed so that they are not likely to be walked on or pinched by
items placed upon or against them. Never take hold of the plug or
cord if your hand is wet, and always grasp the plug body when
connecting or disconnecting it.
4. Nonuse Periods - When the unit is not used, turn the power off.
When left unused for a long period of time, the unit should be
unplugged from the household AC outlet.
6. Carts and Stands - The unit should be used only with a cart or
stand that is recommended by the manufacturer.
The unit and cart combination should be moved with care.
Quick stops, excessive force, and uneven sur¬
faces may cause the unit and cart combination to
overturn.
7. Wall or Ceiling Mounting - The unit should not be mounted to a
wall or ceiling, unless specified in this operating instructions.
Maintenance
Clean the cabinet, panel and controls with a soft cloth lightly moist¬
ened with mild detergent solution.
Do not use any type of abrasive pad, scouring powder or solvent
such as alcohol or benzine.
instaliation
Environment
1. Water and Moisture - Do not use this unit near water-for ex¬
ample, near a bathtub, washbowl, swimming pool, or the like.
Damp basements should also be avoided.
2. Condensation - Moisture may form on the lens in the following
conditions...
• immediately after a heater has been turned on.
• in a steamy or very humid room.
• when the unit is suddenly moved from a cold environment to a
warm one.
If moisture forms inside this unit, it may not operate properly. To
correct this problem, turn on the power and wait about one hour
for the moisture to evaporate.
3. Heat - The unit should be situated away from heat sources such
as radiators and the like. It also should not be placed in tempera¬
tures less than 5' C (41* F) or greater than 35* C (95* F).
Placement
1. Ventilation - The unit should be situated so that its location or
position does not interfere with its proper ventilation. Allow 10 cm
(4" ) clearance from the rear of the unit.
2. Foreign Material - Care should be taken so that objects do not
fall into and liquids are not spilled into the unit. Do not subject this
unit to excessive smoke, dust, mechanical vibration, or shock.
3. Magnetism - The unit should be situated away from equipment
or devices that generate strong magnetic fields.
4. Stacking - Do not place heavy objects, other than system com¬
ponents, on top of the unit.
5. Surface - Place the unit on a flat, level surface.
Service
1. Damage Requiring Service ~ The unit should be serviced by
qualified service personnel when:
(a) The AC power supply cord or the plug has been damaged; or
(b) Objects have fallen or liquid has been spilled into the unit; or
(c) The unit has been exposed to rain; or
(d) The unit does not appear to operate normally or exhibits a
marked change in performance; or
(e) The unit has been dropped, or the enclosure damaged.
2. Servicing - The user should not attempt to service the unit be¬
yond that described in the operating instructions. All other servic¬
ing should be referred to an authorized service personnel.
(Only for U.S.A)
Call 1-800-545-2672 for the address of an authorized factory ser¬
vice nter.
Cautions on moving this unit
Before moving the changer to another location, be sure to
remove all discs from the slots and turn off the changer.
Failure to do so will expose the compact discs and the changer
to the risk of severe damage.
CAUTION
The changer mechanism automatically locks when power is
turned off, to protect it against damage in transport.
Therefore, always press POWER and make sure “OFF appears
on the display _befoie you.unpluq the changer.
Other cautions
Outside light or noise may sometimes cause the changer to
detect a disc when there isn’t one. However, the changer always
correctly detects the disc when in the play mode no matter what.
Do not leave the front panel open. Infiltrating dust or other mat¬
ter may lead to damage or malfunctions.

Technics SL-MC60 Specifications

General

Brand	Technics
Model	SL-MC60
Category	CD Player
Language	English