"T1
l:
::;
,.,
,...
,
o'
:::r
;
V\
Ill:>
if!
j-o
f
i<
:1""\
':xl
,
"T1
,I:
I::!
'n
...
10'
:::r
m
C.
;::;:
::;
~
is
01
J
III 0
,~
V;'
31"1
III
::;
,...
tl:l
~
~
~.
;r'\
,
VI
lro
!
...
!e:
,i:l
r------
i"tl
iij
;
'<
:g"
'1"1
!~
6
DVC
is
in recording pause
mode.
EN
57
DVC
is
fast forwarding.
(in stop mode)
DVC
is
fast reversing.
(in stop mode)
DVC
is
fast reversing.
(standard speed)
DVC
is
fast reversing.
(faster than above)
DVC
is
fast reversing.
(faster than above)
DVC
is
in slow reverse
playback.
DVC
is
in recording.
When
the
DVe
is
not
in
camera
mode
...
o
IT
fC
: 0
DVC
is
fast forwarding.
(standard speed)
DVC
is
fast forwarding.
(faster than above)
DVC
is
fast forwarding.
(faster than above)
DVC
is
slow forwarding.
(standard speed)
DVC
is
slow forwarding.
(faster than above)
DVC
is
slow forwarding.
(faster than above)
DVC
is
in pause mode.
The
menu changes according
to
what mode
of
Dve
Switch the mode on the
DVC
to
playback mode for the dubbing
information.
DO
6.
Product
name
of
your
DVC
•
If
the
unit
cannot recognize
the
input
signal
from
the
DVC
or
the
unknown
product, "No Device"
or
"****"
will appear instead.
7.
Status
of
the
current
operation
and
the
time
counter
Each
icon means (Available icons
may vary
depending
on
the
DVC):
o
DVC
is
in stop mode.
[>
DVC
is
in playback mode.
4
When
the
DVe is
i in
video
mode
...
[~n~
~
2
The
following
instructionsare described
with
the
operations using
the
remote
control
of
this
unit.
DVDUBBING
1.DV
icon
2.
Indicator
of
active
device
• When
the
"Control"
is
highlighted, press [ENTER]
to
display
the
item selection.
Use
[.
I
T]
to
select
the
device you
wish
to
operate, then press
[ENTER]
to
activate.
• Select "DVD"
to
control this unit.
• Select
"DVC
to
control your
DVC.
3.
Recording
audio
mode
• Other than
the
DVC
is
in stop
mode,
the
"DV Audio" can be
selected.
Press
[ENTER]
to
display
the
item
selection and
then
use
[.
I
T]
to
select the audio you
wish
to
output.
Press
[ENTER]
again
to
activate.
• Select "Stereo1"
to
dub
the
stereo
sound.
• Select "Stereo2"
to
dub
the
sound
with
after recording sound.
• Select "Mix"
to
dub
the
stereol
and stereo2.
4.
Indicator
of
dubbing
function
• When
the
unit
is
ready
for
dubbing,
"Start
Rec"
will appear.
• When
the
unit
is
in
dubbing,
"Pause
Rec"
will appear.
5.
Channel
position
• When you select "L3 (DV-IN)" by
using [INPUT
SELECT
-€>]
or
[CH A I
V],
"L3
(DV-IN)" will
appear.
3
~
You cannot control
the
DVC
in
VCR
mode. For
dubbing
onto
VCR,
refer
to
page 59.
This
function
helps you
to
easily
dub
the
contents
of
the
DVC
(digital video camcorder)
to
this unit.
You can control basic operations
of
the
DVC
from
the
remote control
of
this
unit
such
as
playback, fast forward
or
reverse and stop all operations
if
the
DVC
is
in video mode.
Use
the
DV
cable
that
has
4-pin
input
jack and
is
compliance
with
the
IEEE1394
standards. When you connect
to
DV
input
jack on
the
front
of
this unit, select
"L3(DV-IN)" position by using [INPUT
SELECT
-€>] or [CH A I
V]
on
the
remote control and press [DISPLAY]
to
show
the
DV
dubbing
information
for
the
operation
of
your
DVC.
...
Guide
to
DV
_~Dd On-S~r.eeo
Dis
To Next Page
Loading...
Need help?
General
