T
troyfordSep 18, 2025
What to do if my TSC Barcode Reader says 'Carriage Open'?
- JJames BauerSep 18, 2025
If your TSC Barcode Reader displays 'Carriage Open', it means the printer carriage is open. Close the print carriage to resolve this issue.
To Next PageTo Next PageTo Previous PageTo Previous Page
What to do if my TSC Barcode Reader says 'Carriage Open'?
If your TSC Barcode Reader displays 'Carriage Open', it means the printer carriage is open. Close the print carriage to resolve this issue.
How to improve print quality on a TSC printer?
If you're experiencing poor print quality on your TSC printer, consider these solutions: * Reload the supply. * Clean the print head and platen roller. * Adjust the print density and print speed. * Run a printer self-test and check the print head test pattern for missing dots. * Change to a proper ribbon or label media. * Adjust the printhead pressure adjustment knob. * Ensure the release lever properly latches the printhead.
What to do when my TSC MB240 says 'No Ribbon'?
If your TSC printer indicates 'No Ribbon': * Supply a new ribbon roll. * Refer to the user’s manual for instructions on reinstalling the ribbon.
What to do if my TSC Barcode Reader says 'No Paper'?
If your TSC Barcode Reader shows 'No Paper', it might be due to an empty label roll. Replace it with a new one. If that's not the issue, the label roll might be installed incorrectly. Refer to the user’s manual to reinstall the label roll correctly. Also, the gap/black mark sensor may not be calibrated; try calibrating it.
What to do if my TSC Barcode Reader displays 'No Ribbon'?
If your TSC Barcode Reader displays 'No Ribbon', it could be that the ribbon roll is depleted. Replace it with a new ribbon roll. Alternatively, the ribbon might be installed incorrectly. Consult the user’s manual for instructions on how to reinstall the ribbon correctly.
How to fix a TSC Barcode Reader when the power indicator does not illuminate?
If the power indicator on your TSC Barcode Reader does not illuminate, first check if the power cord is properly connected to both the printer and the outlet. If it is, ensure that the power switch is turned on.
Why is my TSC Barcode Reader not printing?
If your TSC Barcode Reader isn't printing, first ensure the interface cable is securely connected; if not, reconnect it or try a new cable. For wireless or Bluetooth connections, try resetting the wireless device settings. Also, verify that the correct printer port is selected in the Windows driver. Another solution is to clean the printhead. If none of these work, turn off the printer and check the printhead's harness connector to ensure it's properly connected. Finally, check your program to ensure there's a PRINT command at the end of the file and that each command line ends with CRLF.
Why is there no print on the label from my TSC Barcode Reader?
If your TSC Barcode Reader isn't printing on the label, make sure the label or ribbon is loaded correctly by following the instructions. Ensure that you are using compatible ribbon and media. Verify the ribbon-inked side. Also, check that the print density setting is correct.
How to correct the printing position of small labels on a TSC MB240?
If the printing position of a small label is incorrect on your TSC printer: * Calibrate the sensor sensitivity again. * Set the correct label size and gap size. * Press [Menu] [Setting] [Shift Y] to fine tune the parameter of Shift Y. * If using BarTender software, set the vertical offset in the driver.
What to do if my TSC MB240 shows 'No Paper'?
If your TSC printer indicates 'No Paper', you should: * Supply a new label roll. * Refer to the user’s manual for instructions on reinstalling the label roll. * Calibrate the gap/black mark sensor.
General| Print Method | Thermal Transfer/Direct Thermal |
|---|---|
| Resolution | 203 dpi |
| Processor | 32-bit RISC CPU |
| Operating Humidity | 25-85% non-condensing |
| Connectivity | USB 2.0, RS-232 |
| Media Sensor | Reflective, Transmissive |
| Media Type | Continuous, Die-cut, Black mark, Fan-fold, Notched |
| Media Width | 25.4 mm |
| Media Thickness | 0.06 mm |
| Media Core Diameter | 25.4 mm (1") |
| Media Max Roll Diameter | 127 mm (5") |
| Ribbon Width | 110 mm |
| Ribbon Length | 300 m |
| Ribbon Core Diameter | 25.4 mm (1 inch) |
| Power | 100 - 240 VAC, 50/60 Hz |
| Maximum Print Length | 9999 mm |
| Label Width | 25.4 mm |
| Label Thickness | 0.06 mm |
| Power Supply | 100-240V AC, 50-60Hz |
| Operating Temperature | 5°C - 40°C |
| Storage Temperature | -20°C - 60°C |
| Certifications | CE |
