VTech DM271 User Manual

How the system works
* The combin ation of sensors depe nds on the package you purc hased.
DM271 Baby monitor
Receive aler ts on your
parent unit when t here’s
activit y in your child’s
room – from an ope n door
or window to movemen t in
the crib.
Motion Sensor
Lets you know when
there are visito rs,
intruders, o r pets
moving around your
home.
Open/Closed Sensor
Apply this ma gnetic
Open/ Closed Sensor to a
door, window, or medic ine
cabinet to know i f it is
open or close d.
4
Check and locate
Check the motion sensor
before use
Test the sensor signal
strength
NOTES
If No signal o r Weak signal
message is d isplayed in sensor
setup mode, or i f you do not
receive an al ert when you open
the door, move the ba se closer to
the mountin g location or move the
sensor clo ser to the base.
Use adhesive tape to hold the
sensor temporarily in place.
•
•
Use your parent unit t o enter
the Sensor s ettings menu , and
then select t he Check sign al
menu. Follow the st eps to test
the sensor’s sig nal strength, a nd
then exit the sen sor setup mode.
Make sure there is a g ood signal
received when t here is motion.
Refer to Sensor n otification s
section in t he User’s manual for
the alerts .
If your package includes
a Motion Sensor, please
read the following
section.
Motion Sensor
installation
1
Parts checklist
1 set for DM271-110
Motion Sensor
Screw for
mounting
brackets x 2
Anchor for
mounting
brackets x 2
Open the battery
compartment case
2
Power
The Motion Sens or detects moti on
with one-m inute cool of f time.
Once motion i s detected, the
sensor will on ly start to dete ct
motion again af ter one minute.
The Motion Sen sor is more
sensitive in de tecting motio ns
crossing th e space in front of th e
sensor than th at moving towards
the sensor.
The Motion Sen sor can detect
motion occ urring at distan ces up
to 40 feet (12 meters) when it is
mounted at a heigh t of 7.9 feet
(2.4 meter s).
It is recomme nded to mount the
sensor at the height between
6.2 feet (1.9 meters) and 7.5 feet
(2.3 meters) for optimal dete ction
coverage.
For motion de tection of ba bies
or pets:
If you use the Moti on Sensor only
to detect the mot ion of babies or
pets, you can moun t the sensor
at a lower positio n to shorten
the minimum di stance before
reaching the d etection area . It is
recommend ed to mount it at the
height 3.3 feet (1 meter) for optimal
detection of b abies or pets.
Up to 34.4
feet
(10.5 meters)
Side view
Detectio n
area
78
o
Top view
Shooting area
19.7 inches
60 degrees
22.8 inches
Shooting area
19.7
inches
50 degrees
18.3
inches
63 inches
87
o
Detectio n
area
1.3 feet
(0.4 meter)
10
o
Height: 6. 9 feet (2.1 meters)
Height: 6.9 feet (2.1 meters)
Detectio n
area
78
o
87
o
Detectio n
area
0.7 feet
(0.2 meter)
10
o
Height: 3. 3 feet (1 meter)
Up to 16.4
feet
(5 meters)
Height: 3.3 feet (1 meter)
Top view
Side view
Baby Monitor installation
1
Parts checklist
2
Connect
Parent unit
Test your baby monitor
3
Check and Locate
3
2
THIS SIDE UP
3
2
THIS SIDE UP
3
2
THIS SIDE UP
3
2
THIS SIDE UP
Battery compartment cover Battery
Parent unit adapter Baby unit Baby unit adapter
Positioning your baby monitor
Install the battery
6
2
5
1
8
4
7
3
6
2
5
1
8
4
7
3
6
2
5
1
8
4
7
3
6
2
5
1
8
4
7
3
6
2
5
1
8
4
7
3
6
2
5
1
8
4
7
3
6
2
5
1
8
4
7
3
6
2
5
1
8
4
7
3
6
2
5
1
8
4
7
3
6
2
5
1
8
4
7
3
6
2
5
1
8
4
7
3
CAUTION
Keep the baby uni t out of the reach of the baby. Never pl ace
or mount the ba by unit inside the baby’s cr ib or playpen.
Do not expose t he baby unit to extreme heat o r direct sunlight.
•
•
1 set for DM271/DM271-102/DM271-110
At least 1
mete
r
(3
fe
et
)
At least 1 meter (3 feet)
Press to turn on the
projector.
It projects so me colorfu l
images to the envi ronment.
Adjust the ang le of the baby
unit so that the i mages are
clearly proj ected to the
ceiling or a wall.
At least 1
mete
r
(3
fe
et
)
At least 1 meter (3 feet)
Connect the baby monitor
3
Motion Detection
NOTE
The numeric al values in the
illustrat ions are for conceptua l
reference o nly. The actual ang les
and distan ces may vary upon the
change in th e mounted height of
the sensor.
•
Install Motion Sensor Battery
NOTES
Use only CR123A Lithi um Battery.
When inser ting Battery, ensure
polariti es are correct.
The Motion Sen sor is already
pre-registered to the baby monitor.
For proper op eration, use battery
within the fo llowing temperature
range: 0°F ( -18°C) and 120°F (49°C ).
•
•
•
•
6
2
5
1
8
4
7
3
6
2
5
1
8
4
7
3
Unscrew.
6
2
5
1
8
4
7
3
6
2
5
1
8
4
7
3
Lithium battery
Double-sided
mounting tape
Screw for
back cover x 3
Anchor for
back cover x 3
Mounting bracket
on mounting base
with screw

VTech DM271 Specifications

General

Brand	VTech
Model	DM271
Category	Baby Monitor
Language	English