CONNECT 4G-X CELL PHONE SIGNAL BOOSTER
15
ENGLISH
______
Specifi cations
Connect 4G-X
Model Number 460004
Product Number U471004
FCC PWO460004
IC 4726A-460004
Connectors N-Female
Antenna Impedance 50 Ohms
Frequency 698-746 MHz, 746-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz
Passband Gain (nominal)
700
MHz Band12/17
59.1
700MHz Band13
56.2
800MHz
59.2
1700/2100
MHz
64.8
1900
MHz
67.8
20 dB Bandwidth (MHz)
700
MHz Band12/17 700MHz Band13 800MHz 1700/2100MHz 1900MHz
Typical
Maximum
28.6
33.2
27.6
33.2
38.3
40.4
80.8
81.0
76.9
80.0
Power output for single cell
phone (Uplink) dBm
700
MHz Band12/17 700MHz Band13 800MHz 1700MHz 1900MHz
23.2 23.8 25.2 22.5 22.1
Power output for single cell
phone (Downlink) dBm
700
MHz Band12/17 700MHz Band13 800MHz 2100MHz 1900MHz
-0.4 -2.1 -2.0 0.9 -1.4
Power output for multiple
received channels (Uplink) dBm
No. Tones
Maximum Power
700
MHz Band12/17 700MHz Band13 800MHz 1700MHz 1900MHz
2 24.5 22.1 24.5 22.3 21.4
3 20.9 18.5 21.0 18.7 17.8
4 18.4 16.0 18.5 16.2 15.3
5 16.5 14.1 16.6 14.3 13.4
6 14.9 12.5 15.0 12.7 11.8
Power output for multiple
received channels
(Downlinklink) dBm
Maximum Power
No. Tones 700
MHz Band12/17 700MHz Band13 800MHz 2100MHz 1900MHz
2 0.2 -2.2 -0.8 0.7 2.1
3 -3.3 -5.7 -4.3 -2.8 -1.4
4 -5.8 -8.2 -6.8 -5.3 -3.9
5 -7.7 -10.1 -8.7 -7.2 -5.8
6 -9.3 -11.7 -10.3 -8.8 -7.4
Noise Figure 5 dB nominal
Isolation > 90 dB
Power Requirements
110-240 V AC, 50-60 Hz, 20 W
The term “IC” before the radio certification number only signifies that Industry Canada technical specifications
were met.
Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot
be adjusted without factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not
alter incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the
Signal Booster is not in use for five minutes, it will reduce gain until a signal is detected. If a detected signal is
too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booser will automatically
reduce the gain on that specific band.
The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when
multiple carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output
signal is re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of
input power or gain reduction and not by an attenuator at the output of the device.
To Next Page
Loading...
Need help?
General