Yamaha Electone ME-35A User Manual

6. Transferring Information to a Cassette
CASSETTE
The C.S.P. and Registration Memory data
can be transferred to а cassette tape.
TO CASSETTE
1 Connect a data recorder
TO FROM
to the Electone. CASSETTE CASSETTE
(INPUT Jack]
Connect the TO CASSETTE jack on the Electone to the IN (or MIC) jack on your data
recorder using a shielded cable. Then insert a cassette tape. (Though an ordinary audio
cassette recorder can be substituted for the data recorder, the use of a recorder specifically
designed for data recording is recommended.)
2 Press the RECORD button on the data recorder.
If your recorder has a counter, you may wish to note the starting and ending numbers to
facilitate later use.
3 Turn to the Multi Menu page marked “Cassette” then press the TO
CASSETTE button.
| ππα------ :
This starts the transfer of the C.S.P. data and also Registration
Memory data in the Electone to the cassette tape.During this
pas
procedure, the TO CASSETTE indicator lamp will stay on.
Once this procedure is completed, a buzzer will sound, the
lamp will flash briefly, then go off. When the lamp goes out,
press the STOP button of the data recorder.
FROM CASSETTE
1 Connect a data recorder
to the Electone.
TO FROM
CASSETTE CASSETTE
Connect the FROM CASSETTE jack on the Electone to the OUT (or EAR) jack on your data
recorder using a shielded cable. Insert the cassette tape on which you have saved the
desired data and rewind it to the point where the saving operation was started.
Set the playback volume of the data recorder to a level slightly higher than medium level.
2
Press
the
FROM
CASSETTE
button
in
Multi
Menu.
[NN
.
3 Press the PLAY button on the data recorder. е
This starts the transfer of the data from the cassette tape to the Electone. During this
procedure, the FROM CASSETTE indicator lamp will stay on. Once this operation is
completed, a buzzer will sound, the lamp will flash briefly, then go off.
When the lamp goes out, press the STOP button of the data recorder.
25
[When Data Cannot be Transferred]
When the TO CASSETTE procedure has not been
properly performed, the TO CASSETTE lamp will
remain illuminated. When the FROM CASSETTE
function has not been properly performed, either
three warning beeps are sounded or the FROM
CASSETTE lamp remains lit up. In such cases,
confirm the checkpoints below:
(1)Is the cable between the Electone and data
recorder securely connected?
(2) Are the connecting jacks plugged into the
proper sockets or is there an error in the
operating procedure?
(3) Is the playback volume of the recorder at the
proper level?
When the VOLUME control has a 10-step scale,
set the volume from 6 to 8.
(4) Is the recording head dirty?
(5) Is the proper cassette tape being used?
* Be sure to use a tape specifically designed for
computer use or a normal low-noise audio tape
(30- or 45-min. tape).
* Use only new tapes whenever possible.
* Check the tape for twists, seams, wrinkles, etc.
(When using tape with a "leader" (i.e. normal
audio tape), fast forward the tape past this
“leader”.)
(6) Is an appropriate recorder being used?
With an ordinary audio cassette recorder,
some of its characteristics may render it un-
usable for data recording or cause difficulties
in recording. Use of a data recorder is strongly
recommended.
[Additional Information]
@The TO CASSETTE or FROM CASSETTE
procedure normally requires about 60 seconds
e During the TO CASSETTE or FROM CASSETTE
procedure, you cannot play your Electone. Also,
all indicator lamps on the control panel will
go out.
e When the FROM CASSETTE procedure is per-
formed, any data previously stored in the
Electone will be erased.
Uo ee ш]
INNUIT UM
|
|

Yamaha Electone ME-35A Specifications

General

Brand	Yamaha
Model	Electone ME-35A
Category	Musical Instrument
Language	English