EasyManuals Logo

Yamaha MT 10 User Manual

Yamaha MT 10
120 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #26 background imageLoading...
Page #26 background image
Instrument and control functions
5-4
1
2
3
4
5
6
7
8
9
10
11
12
Right
EAU78400
Headlight and Pass/LAP switch
/ ” and “ /LAP”
Set this switch to “ ” for the high
beam and to “ ” for the low beam.
While the headlights are set to low
beam, push the switch downward (to-
wards /LAP) to flash the headlights
and to mark the start of each lap when
using the lap timer.
EAU66040
Turn signal switch “ /
To signal a right-hand turn, push this
switch to “ ”. To signal a left-hand
turn, push this switch to “ ”. When re-
leased, the switch returns to the center
position. To cancel the turn signal
lights, push the switch in after it has re-
turned to the center position.
EAU66030
Horn switch “
Press this switch to sound the horn.
EAU66060
Stop/Run/Start switch “ / /
To crank the engine with the starter, set
this switch to “ ”, and then push the
switch down towards “ ”. See page
7-1 for starting instructions prior to
starting the engine.
Set this switch to “ ” to stop the engine
in case of an emergency, such as when
the vehicle overturns or when the throt-
tle cable is stuck.
EAU66010
Hazard switch “
With the key in the “ON” or “ ” posi-
tion, use this switch to turn on the haz-
ard lights (simultaneous flashing of all
turn signal lights).
The hazard lights are used in case of
an emergency or to warn other drivers
when your vehicle is stopped where it
might be a traffic hazard.
NOTICE
ECA10062
Do not use the hazard lights for an
extended length of time with the en-
gine not running, otherwise the bat-
tery may discharge.
EAU73951
Cruise control switches
See page 4-3 for an explanation of the
cruise control system.
EAU78391
Select switch “ /
This switch is used to change YRC
modes or edit the PWR, TCS, and ERS
settings. (See page 5-11.)
EAU78382
Mode switch “MODE”
Use the mode switch to change YRC
modes or edit the PWR, TCS, and ERS
settings from the main screen.
Push this switch to scroll left to right
among the MODE, PWR, TCS, and
ERS items.
TIP
The traction control system can
1. Stop/Run/Start switch “ / /
2. Wheel switch “
1
2
BW8-9-20_1.book 4 ージ 016年12月13日 火曜日 午前11時18分

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Yamaha MT 10 and is the answer not in the manual?

Yamaha MT 10 Specifications

General IconGeneral
Engine TypeLiquid-cooled, 4-stroke, DOHC, 4-valve
Displacement998cc
Bore x Stroke79.0 mm x 50.9 mm
Compression Ratio12.0 : 1
Maximum Power118.0 kW (160.4 PS) @ 11, 500 rpm
Fuel SystemFuel Injection
Ignition SystemTCI
TransmissionConstant mesh, 6-speed
Final DriveChain
Front SuspensionTelescopic forks
Front Tyre120/70 ZR17 M/C (58W)
Rear Tyre190/55 ZR17 M/C (75W)
Overall Length2, 095 mm
Overall Width800 mm
Overall Height1, 110 mm
Seat Height825 mm
Wheelbase1, 405 mm
Minimum Ground Clearance135 mm
Wet Weight210 kg
Fuel Tank Capacity17 litres
Maximum Torque111 Nm (11.3 kg-m) @ 9, 000 rpm
Rear SuspensionSwingarm
Front BrakeDual hydraulic disc
Rear BrakeHydraulic disc
FrameAluminum Deltabox

Related product manuals