Name: Cisco ASR 900 Series
Brand: Cisco
Rating: 4 (1 reviews)

To Next Page

To Previous Page

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

New Software Features in Cisco IOS XE Release 3.6S

The following are the new software features introduced in Cisco IOS XE Release 3.6S:

Note Many of the features supported on the Cisco ASR 903 Router require a license for use. For more

information about supported licenses, see Software Licensing Overview, page 2.

• Any Transport over MPLS (AToM)—ATM AAL5 over MPLS (AAL5oMPLS)—The AAL5

Transport over MPLS feature provides an ATM permanent virtual circuit (PVC) transport service

for transporting AAL5 PDUs across an IP/MPLS backbone with rate-limit policing and configurable

PVC priority value. A dynamic MPLS tunnel is configured to enable label imposition and

disposition of encapsulated ATM PDUs transported between two edge routers having a Label

Distribution Protocol (LDP) neighbor relationship. For details about this feature, see:

–

http://www.cisco.com/en/US/docs/ios-xml/ios/mp_l2_vpns/configuration/15-2s/mp-any-transpo

rt.html

–

http://www.cisco.com/en/US/docs/ios/ios_xe/mpls/configuration/guide/mp_any_transport_xe.ht

–

http://www.cisco.com/en/US/docs/ios/mpls/configuration/guide/mp_any_transport.html

–

http://www.cisco.com/en/US/docs/wireless/asr_900/software/guide/chassis/Release3.6.0S/ASR

903-Chassis-SW-36.html

• BFD IPv6 Encapsulation—This feature introduces support for IPv6 addresses with the BFD

protocol. For details about this feature, see

http://www.cisco.com/en/US/docs/ios/ipv6/configuration/guide/ip6-bfd.html

• BGP PIC Edge for IP/MPLS—This feature introduces support for BGP PIC Edge for IP/MPLS for

sub-second convergence for IP and MPLS-VPN. For details about this feature, see:

–

http://www.cisco.com/en/US/partner/docs/ios-xml/ios/iproute_bgp/configuration/xe-3s/asr903/ir

g-xe-3s-asr903-book.html

–

http://www.cisco.com/en/US/docs/ios/iproute_bgp/configuration/guide/irg_bgp_mp_pic.html

–

http://www.cisco.com/en/US/docs/ios-xml/ios/iproute_bgp/configuration/15-2mt/irg-bgp-mp-pi

c.html

• CFM over EFP interface with xconnect—This feature provides support for IEEE 802.1ag draft

8.1-compliant CFM functionality on pseudowire & VFI interfaces. For details about this feature,

see:

–

http://www.cisco.com/en/US/docs/wireless/asr_900/feature/guides/CFM_EFP_xconnect.html

–

http://www.cisco.com/en/US/docs/routers/7600/install_config/ES40_config_guide/es40_chap4.

html

• CFM on Port-Channel Interfaces—This feature provides support for IEEE 802.1ag (CFM) on

port-channel interfaces for end-to-end connectivity fault management on Ethernet networks. For

details about this feature, see:

–

http://www.cisco.com/en/US/docs/ios/cether/configuration/guide/ce_cfm.html

–

http://www.cisco.com/en/US/docs/ios/ipsla/configuration/guide/sla_metro_ethernet.html

–

http://www.cisco.com/en/US/partner/docs/ios-xml/ios/cether/configuration/xe-3s/ce-cfm.html

Brand	Cisco
Model	ASR 900 Series
Category	Network Router
Language	English

Cisco ASR 900 Series Release Notes

Table of Contents

Other manuals for Cisco ASR 900 Series

Questions and Answers:

Cisco ASR 900 Series Specifications

Related product manuals