Cisco RV110W Administration Guide

Configuring the Firewall
Configuring Access Rules
Cisco RV110W Administration Guide 89
4
• Te l n e t S e c o n d a r y
• Te l n e t S S L
• Voice (SIP)
STEP 6 (Optional) Click Configure Services to go to the Service Management page to
configure the services before applying access rules to them.
See Configuring Services Management for more information.
STEP 7 In the Source IP field, select the users to which the firewall rule applies:
• Any—The rule applies to traffic originating on any host in the local network.
• Single Address—The rule applies to traffic originating on a single IP address
in the local network. Enter the address in the Start field.
• Address Range—The rule applies to traffic originating from an IP address
located in a range of addresses. Enter the starting IP address in the Start
field, and the ending IP address in the Finish field.
STEP 8 In the Log field, specify whether the packets for this rule should be logged.
To log details for all packets that match this rule, choose Always from the drop-
down menu. For example, if an outbound rule for a schedule is selected as Block
Always, for every packet that tries to make an outbound connection for that
service, a message with the packet's source address and destination address
(and other information) is recorded in the log.
Enabling logging may generate a significant volume of log messages and is
recommended for debugging purposes only.
Choose Never to disable logging.
Note: When traffic is going from the LAN or DMZ to the WAN, the system requires
rewriting the source or destination IP address of incoming IP packets as they pass
through the firewall.
STEP 9 In the QoS Priority field, assign a priority to IP packets of this service. The priorities
are defined by QoS Level: (1 (lowest), 2, 3, 4 (highest)).
STEP 10 In the Rule Status field, check the box to enable the new access rule.
STEP 11 Click Save.

Cisco RV110W Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100Base-T(X)
Networking standards	IEEE 802.11b, IEEE 802.11e, IEEE 802.11g, IEEE 802.11n, IEEE 802.1p, IEEE 802.3, IEEE 802.3u
VPN tunnels quantity	10
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet LAN interface type	Fast Ethernet
Wi-Fi standards	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Channels quantity	13 channels
Top Wi-Fi standard	Wi-Fi 4 (802.11n)
Ethernet LAN (RJ-45) ports	4
Input voltage	12 V
Rack mounting	No
Number of users	32 user(s)
Weight (imperial)	0.61 lbs
Dimensions (WxDxH)	150 x 150 x 30 mm
Operating temperature (T-T)	32 - 104 °F
Compliance industry standards	IEEE 802.3, IEEE 802.3u
Supported data transfer rates	10/100Mbps
Dimensions (W x D x H) (imperial)	5.91 x 5.91 x 1.18 \
WLAN data transfer rates supported	11, 54 Mbit/s
Supported network protocols	PPPoE, DHCP, PPTP, L2TP, IGMP, RSTP
Antennas quantity	2
Antenna gain level (max)	1.8 dBi
Firewall security	VPN
Security algorithms	WEP, WPA, WPA2, WPS
MAC address filtering	-
Product color	Black
Certification	FCC, CE, IC, cUL, Wi-Fi
Storage temperature (T-T)	-20 - 70 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 85 %

Weight and Dimensions

Width	150 mm
Height	30 mm
Weight	300 g