Cisco WAP571 User Manual

Cisco WAP571 Wireless Access Point 2
Cisco WAP571 Wireless-AC/N Premium
Dual Radio Access Point with PoE Setup
Features
Front Panel
The front panel of the device consists of a single system LED. For a full
description of the colors of the light and its indications, see Verifying the
Hardware Installation, page 6.
A Kensington lock slot is found above the light.
Back Panel
The back panel of the device has two RJ-45 Ethernet ports. Facing the
back of the device, the right port (labeled “ETH0/PD”) is an 802.3at &
802.3af Power over Ethernet (PoE) port which is used to power your
device. The left port (labeled “ETH1”) is a general Gigabit Ethernet LAN
interface. Both are auto-sensing, Gigabit Ethernet (802.3) ports used to
connect your WAP devices to network devices, such as computers,
routers, or switches. We strongly recommend that you use a Category
5e or better cable for Gigabit connectivity.
The side panel of the device has a Reset button. See Rebooting the
Devices or Returning them to their Factory Default Settings, page 10
for information on the Reset button.
Default Setting
If you are using a Cisco RV Series router, the default range for the DHCP
assigned address is from 192.168.1.100 to 192.168.1.254. Any device
connecting to the same LAN will be assigned an IP address in this range.
If your network does not have an existing DHCP server, the WAP571 will
start a DHCP server for WLAN stations and stop the DHCP client when
WAP571 is in factory default. The DHCP server will assign the IP address
from 192.168.1.20 to 192.168.1.100.
Parameter Default Value
Username cisco
Password cisco
LAN IP Address DHCP address assigned
by server
Fallback LAN IP 192.168.1.245
Subnetwork Mask 255.255.255.0
2

Cisco WAP571 Specifications

General

2.4 GHz	Yes
Bandwidth	5 GHz
Modulation	16-QAM, 64-QAM, 256-QAM, BPSK, OFDM, QPSK
Number of users	200 user(s)
Channels quantity	155 channels
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11e, IEEE 802.11g, IEEE 802.11i, IEEE 802.11n, IEEE 802.1D, IEEE 802.1Q, IEEE 802.1x, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Receiver sensitivity	2.4 GHz 802.11b: -86 dBm 11Mbps 802.11g: -74 dBm 54 Mbps 802.11n(HT20): -71 dBm MCS7 802.11n(HT40): -68 dBm MCS7 5 GHz 802.11a: -90 dBm 6 Mbps 802.11a: -75 dBm 54 Mbps 802.11ac(HT20): -63 dBm MCS9 802.11ac(HT40): -60 dBm MCS9 802.11ac(HT80): -58 dBm MCS9
Throughput data rate	1900 Mbit/s
Spread spectrum method	DSSS
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Maximum data transfer rate	600 Mbit/s
Flash memory	128 MB
Internal memory	256 MB
Operating system installed	Linux
Security algorithms	HTTPS, SNMP, SSID, WDS, WPA, WPA2
Auto Wireless Distribution System (WDS)	No
Placement	Ceiling, Table, Wall
Certification	UL 60950-1, CAN/CSA-C22.2 No. 60950-1, IEC 60950-1, EN 60950-1, FCC Part 15.247, 15.407, RSS-210, EN 300.328, EN 301.893, AS/NZS 4268.2003, FCC 15.107 + 15.109, ICES-003, EN 301.489-1 + -17
Product color	White
Cable lock slot type	Kensington
Supported network protocols	NTP, HTTP/HTTPS, IPv6
WAN connection	Ethernet (RJ-45)
USB 2.0 ports quantity	-
Ethernet LAN (RJ-45) ports	2
Antenna features	Integrated antenna
Antennas quantity	6
Antenna gain level (max)	1.99 dBi
Power consumption (max)	18 W
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 85 %
Cables included	LAN (RJ-45)

Weight and Dimensions

Width	230 mm
Height	40 mm
Weight	778 g