D-Link DES-1008E User Manual

ENGLISH
5
• Tohelpavoiddamagingyoursystem,besurethevoltageselectionswitch(ifprovided)onthepowersupplyissettomatchthe
power available at your location:
– 115volts(V)/60hertz(Hz)inmostofNorthandSouthAmericaandsomeFarEasterncountriessuchasSouthKoreaandTaiwan.
– 100 V/50 Hz in eastern Japan and 100 V/60 Hz in western Japan.
– 230 V/50 Hz in most of Europe, the Middle East, and the Far East.
• Alsobesurethatattacheddevicesareelectricallyratedtooperatewiththepoweravailableinyourlocation.
• Useonlyapprovedpowercable(s).IfyouhavenotbeenprovidedwithapowercableforyoursystemorforanyAC-poweredoption
intended for your system, purchase a power cable that is approved for use in your country. The power cable must be rated for the
product and for the voltage and current marked on the product’s electrical ratings label. The voltage and current rating of the
cable should be greater than the ratings marked on the product.
• Tohelppreventanelectricshock,plugthesystemandperipheralpowercablesintoproperlygroundedelectricaloutlets.These
cables are equipped with three-prong plugs to help ensure proper grounding. Do not use adapter plugs or remove the grounding
prong from a cable. If you must use an extension cable, use a 3-wire cable with properly grounded plugs.
• Observeextensioncableandpowerstripratings.Makesurethatthetotalampereratingofallproductspluggedintotheextension
cable or power strip does not exceed 80 percent of the ampere ratings limit for the extension cable or power strip.
• Tohelpprotectyoursystemfromsudden,transientincreases and decreasesinelectrical power, use asurgesuppressor,line
conditioner, or uninterruptible power supply (UPS).
• Positionsystemcablesandpowercablescarefully;routecablessothattheycannotbesteppedonortrippedover.Besurethat
nothing rests on any cables.
• Donotmodifypowercablesorplugs.Consultalicensedelectricianoryourpowercompanyforsitemodications.Alwaysfollow
your local/national wiring rules.
• Whenconnectingordisconnectingpowertohot-pluggablepowersupplies,ifoeredwithyoursystem,observethefollowing
guidelines:
– Install the power supply before connecting the power cable to the power supply.
– Unplug the power cable before removing the power supply.
– If the system has multiple sources of power, disconnect power from the system by unplugging all power cables from the power
supplies.

D-Link DES-1008E Specifications

Data Transfer

switching fabric	1.6 Gbps
data transfer rate (Ethernet, half duplex)	10 Mbps
data transfer rate (Ethernet, full duplex)	20 Mbps
data transfer rate (Fast Ethernet, half duplex)	100 Mbps
data transfer rate (Fast Ethernet, full duplex)	200 Mbps

Power

DC input	5V/1.2A
power consumption (standby, DC input)	0.6 watts
power consumption (standby, AC input)	1.4 watts
power consumption (maximum, DC input)	3.3 watts
power consumption (maximum, AC input)	5.2 watts

Operating Environment

operating temperature	32 to 122 ˚F (0 to 50 ˚c)
storage temperature	14 to 158 ˚F (-10 to 70 ˚c)
operating humidity	10% to 90% RH Non-Condensing
storage humidity	5% to 90% RH Non-Condensing

Heat Dissipation

heat dissipation (standby, AC input)	4.774 BTU/h
heat dissipation (maximum, AC input)	17.732 BTU/h

Weight and Dimensions

device dimensions (W x D x H)	6.5” x 4.4” x 1.5” (164.5 x 111.5 x 36.0 mm)