Daewoo DVK-47N User Manual

Setting up your VCR
Once you have connected your VCR and put batteries in the
remote control, you are ready to use the VCR. Before you start,
however, you must be certain to do the following:
• Turn on the television.
• Tune the television to channel 3 or 4 (whichever
channel you selected when connecting the VCR).
Turning the VCR on
1 Press POWER on the remote control. You can also
press POWER on the VCR’s front panel.
2 Set the VCR to VCR mode by pressing TV/VCR on the
remote control if the VCR indication is not lit.
Changing the on-screen menu language
You may select the language in which you would like the
VCR’s menu to be displayed: English, Spanish, or French.
1 Press MENU to display the main menu.
2 Press 5 to select Language.
3 Press 1 to select English, 2 to select Español
or 3 to select Français.
4 Press MENU once to return the main menu, which
will be displayed in the language you selected. Press
MENU again to exit the menu system and return to
normal viewing.
MENU
1 TIMER RECORDINGS
2 CLOCK SET
3 CHANNEL SET
4 FUNCTIONS
5 LANGUAGE SELECT
MENU Exit
1211
• If your cable system requires you to use a
converter box for all channels, connect the
incoming cable to the IN terminal on the converter
box. Connect another cable between the OUT
terminal on the converter box and the ANT. IN
terminal on the VCR. Keep your VCR tuned to channel
3 or 4 and change channels using the converter box.
• If your cable system only requires you to use a
converter box for some channels (i.e., pay-TV
channels), follow these steps: Find the primary
incoming coaxial cable. Plug this cable into a splitter
(available at your local electronics store.) Connect
one coaxial cable between one OUT terminal on the
splitter and the IN terminal on the converter box.
Connect another coaxial cable between the other
OUT terminal on the splitter and the A-IN terminal on
an A/B switch (available at your local electronics
store.) Connect a third coaxial cable between the
OUT terminal on the converter box and the B-IN
terminal on the A/B switch.
Connect a coaxial cable between the OUT terminal on
the A/B switch and the ANT. IN on your VCR.
When the A/B switch is in the B position, use the
converter box to change channels ; when the A/B
switch is in the A position, use the VCR to change
channels.
Connecting your VCR, continued
VCR
ANT.IN
VCR
Daewoo Video Cassette Recorder User’s Guide Daewoo Video Cassette Recorder User’s Guide

Daewoo DVK-47N Specifications

System

video signal	NTSC color
channel coverage VHF	Channel 2-13
channel coverage UHF	Channel 14-69
channel coverage CATV	Channels A1-A5, A8, A-W, W+1-W+84
VHF output signal	Channel 3 or 4 (selectable)

Video

video input	Phono-type connector 1.0V (p-p) 75 ohms unbalanced, sync.negative
video output	Phono-type connector 1.0V (p-p) 75 ohms unbalanced, sync.negative
signal to noise ratio	More than 43dB (SP)
horizontal resolution	220 lines

Audio

audio input	Phono-type connector more than 47K ohms -8.8 dBm, unbalanced
audio output	Phono-type connector less than 1.5K ohms -5.8 dBm, unbalanced
frequency response	Normal: 100Hz-l0KHz (SP)
audio signal to noise ratio	Normal: more than 42 dB
audio distortion	Normal: less than 4 % (SP)

Tape Transport

tape width	12.65 mm (1/2”)
tape speed SP	33.35 mm/sec
tape speed EP	11.12 mm/sec
maximum recording time	480 min, with T-160 tape (EP)
rewind/fast forward time	Approx 3 min (T-120 tape)

General

power requirements	AC120V 60 Hz only
power consumption	17 W(under 4W in standby mode)
set dimensions	14.17 x 3.58 x 9.37 inches
carton dimensions	17.52 x 6.11 x 12.21 inches
weight net	6.41 lbs
weight gross	8.37 lbs