EasyManuals Logo
Home>Dell>Server>PowerEdge R730xd

Dell PowerEdge R730xd User Manual

Dell PowerEdge R730xd
239 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #235 background imageLoading...
Page #235 background image
14. For each expansion card you removed in step 10, perform the following steps:
a. Turn off the system and attached peripherals, and disconnect the system from the electrical
outlet.
b. Remove the system cover.
c. Reinstall one of the expansion cards.
d. Install the system cover.
e. Run the appropriate diagnostic test. See the Using system diagnostics section.
If the problem persists, see the Getting help section.
Related Links
Getting help
Using system diagnostics
Safety instructions
Removing the system cover
Removing an expansion card from expansion card riser 2 or 3
Installing an expansion card into the expansion card riser 2 or 3
Installing the system cover
Troubleshooting expansion cards
Prerequisites
CAUTION: Many repairs may only be done by a certified service technician. You should only
perform troubleshooting and simple repairs as authorized in your product documentation, or as
directed by the online or telephone service and support team. Damage due to servicing that is
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions
that are shipped with your product.
NOTE: When troubleshooting an expansion card, you also have to see the documentation for your
operating system and the expansion card.
Steps
1. Run the appropriate diagnostic test. See the Using system diagnostics section.
2. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.
3. Remove the system cover.
4. Ensure that each expansion card is firmly seated in its connector.
5. Install the system cover.
6. Turn on the system and attached peripherals.
7. If the problem is not resolved, turn off the system and attached peripherals, and disconnect the
system from the electrical outlet.
8. Remove the system cover.
9. Remove all expansion cards installed in the system.
10. Install the system cover.
11. Run the appropriate diagnostic test. See the Using system diagnostics section.
If the tests fail, see the Getting help section.
12. For each expansion card you removed in step 8, perform the following steps:
a. Turn off the system and attached peripherals, and disconnect the system from the electrical
outlet.
235

Table of Contents

Other manuals for Dell PowerEdge R730xd

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Dell PowerEdge R730xd and is the answer not in the manual?

Dell PowerEdge R730xd Specifications

General IconGeneral
Tcase72.6 °C
Bus typeQPI
SteppingR2
FSB ParityNo
Scalability2S
Processor codeSR207
Processor cache15 MB
Processor cores6
Processor modelE5-2620V3
System bus rate8 GT/s
Processor seriesIntel Xeon E5-2600 v3
Processor socketLGA 2011-v3
Processor threads12
Processor codenameHaswell
Motherboard chipsetIntel C610
Processor frequency2.4 GHz
Processor cache typeSmart Cache
Processor lithography22 nm
Processor manufacturerIntel
Processor package size52.5 x 45 mm
Processor front side bus- MHz
Processor boost frequency3.2 GHz
Processor operating modes64-bit
ECC supported by processorYes
PCI Express configurationsx4, x8, x16
Supported instruction setsAVX
Thermal Design Power (TDP)85 W
Number of processors installed1
Maximum number of SMP processors2
Maximum number of PCI Express lanes40
Memory types supported by processorDDR4-SDRAM
Memory channels supported by processorQuad
Memory clock speeds supported by processor1600, 1866 MHz
Memory bandwidth supported by processor (max)59 GB/s
Maximum internal memory supported by processor768 GB
HDD size3.5 \
HDD speed7200 RPM
RAID levels0, 1, 5, 6
HDD interfaceSerial ATA, Serial Attached SCSI (SAS)
Total storage capacity4000 GB
Maximum storage capacity99.6 TB
Supported storage drive interfacesSerial ATA
Memory slots24
Internal memory16 GB
Memory clock speed2133 MHz
LAN controllerBroadcom 5720
Cabling technology10/100/1000Base-T(X)
Ethernet interface typeFast Ethernet, Gigabit Ethernet
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Ethernet LAN (RJ-45) ports4
Operating system installed-
Compatible operating systemsMicrosoft Windows Server 2008/2012 SP2, x86/x64 (x64 includes Hyper-VTM )\\r Microsoft Windows Server 2008/2012 R2, x64 (includes Hyper-VTM v2)\\r Microsoft Windows HPC Server 2008\\r Novell SUSE Linux Enterprise Server\\r Red Hat Enterprise Linux\\r VMware ESX
Chassis typeRack (2U)
Power supply750 W
Intel® Virtualization Technology (Intel® VT)VT-d, VT-x
Processor ARK ID83352
Intel Secure Key Technology version1.00
Intel Identity Protection Technology version0.00
PCI Express slots version3.0
On-board graphics card modelNot available
Weight and Dimensions IconWeight and Dimensions
Depth684 mm
Width440 mm
Height87.3 mm

Related product manuals