Dell PowerEdge T410 User Manual

166 Troubleshooting Your System
Troubleshooting an External Tape Drive
1 Try using a different tape cartridge.
2 Ensure that the device drivers for the tape drive are installed and are
configured correctly. See your tape drive documentation for more
information about device drivers.
3 Reinstall the tape-backup software as instructed in the tape-backup
software documentation.
4 Ensure that the tape drive’s interface cable is fully connected to the tape
drive and the external port on the controller card.
5 For SCSI tape drives, verify that the tape drive is configured for a unique
SCSI ID number and that the tape drive is terminated or not terminated,
based on the interface cable used to connect the drive.
See the documentation for the tape drive for instructions on selecting the
SCSI ID number and enabling or disabling termination.
6 Run the appropriate diagnostics tests. See "Running the System
Diagnostics" on page 173.
7 Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
WARNING: Only trained service technicians are authorized to remove the system
cover and access any of the components inside the system. Before you begin this
procedure, review the safety instructions that came with the system.
8 Open the system. See "Opening the System" on page 90.
9 Reseat the controller card in the expansion card slot.
10 Close the system. See "Closing the System" on page 91.
11 Place the system upright and on its feet on a flat and stable surface,
reconnect the system to the electrical outlet, and turn on the system and
attached peripherals.
If the problem is not resolved, see the documentation for the tape drive for
additional troubleshooting instructions.
If you cannot resolve the problem, see "Getting Help" on page 185.
book.book Page 166 Tuesday, June 9, 2009 4:09 PM

Dell PowerEdge T410 Specifications

General

Tcase	77.6 °C
Bus type	QPI
Stepping	B1
FSB Parity	No
Processor code	SLBV4
Processor cache	12 MB
Processor cores	4
Processor model	E5620
System bus rate	5.86 GT/s
Processor series	Intel Xeon 5600 Series
Processor socket	Socket B (LGA 1366)
Processor threads	8
Processor codename	Westmere EP
Motherboard chipset	Intel® 5500
Number of QPI links	2
Processor frequency	2.4 GHz
Processor cache type	Smart Cache
Processor lithography	32 nm
Processor manufacturer	Intel
Processor package size	42.5 X 45 mm
Processor front side bus	- MHz
Processor boost frequency	2.66 GHz
Processor operating modes	64-bit
ECC supported by processor	Yes
Supported instruction sets	SSE4.2
Thermal Design Power (TDP)	80 W
Number of processors installed	1
CPU multiplier (bus/core ratio)	18
Physical Address Extension (PAE)	40 bit
Memory types supported by processor	DDR3 800/1066
Memory channels supported by processor	Triple
Memory clock speeds supported by processor	800, 1066 MHz
Memory bandwidth supported by processor (max)	25.6 GB/s
Maximum internal memory supported by processor	288 GB
HDD size	3.5 \
Optical drive type	DVD-RW
Total storage capacity	250 GB
Maximum storage capacity	12 TB
Number of HDDs supported	6
Memory slots	8x DIMM
Internal memory	4 GB
Memory clock speed	1066 MHz
Internal memory type	DDR3-SDRAM
Maximum internal memory	16 GB
Maximum graphics card memory	8 MB
Graphics card	G200eW
Dimensions (W x D x H) (imperial)	8.58 x 24.28 x 17.52 \
Networking features	Gigabit Ethernet
PS/2 ports quantity	0
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Number of power supply units	-
Compatible operating systems	Microsoft SQL Server 2008 R2/Windows Small Business Server 2008/Essential Business Server 2008/Server 2008 SP2, x86/x64/Server 2008 R2/HPC Server 2008; Novell SUSE Linux Enterprise Server; Red Hat Enterprise Linux.
Chassis type	Tower
Processor ARK ID	47925
Intel® Turbo Boost Technology	1.0

Weight and Dimensions

Depth	616.8 mm
Width	217.9 mm
Height	444.9 mm