Dell PowerEdge T710 User Manual

134 Installing System Components
Installing an Integrated Storage Controller Card
NOTE: Be sure to connect the cables according to the connector labels on the
cables. The cables are not operational if reversed.
1 If applicable, install the RAID battery (see "Installing a RAID Battery" on
page 128) and connect the RAID battery cable to the connector on the
card. See Figure 3-23.
2 Install the integrated storage controller card in the storage-card slot on the
system board. See Figure 6-1 to locate the storage-card slot.
a Holding the card by its edges, position the card so that the card
connector aligns with the storage-card connector on the system board.
b Lower the card into the card guides, and insert the card connector
firmly into the storage-card connector until the card is fully seated and
the blue plastic card guide locks in place over the upper corner of the
card.
3 Connect the storage card to the SAS backplane:
a Connect the CNTL 0 cable connector on the SAS data cable to the
white SAS_0 connector on the SAS card, and the CNTL 1connector
to the black SAS_1 connector on the card. See Figure 3-23.
b Attach the SAS A cable connector to the SAS A connector on the
backplane.
c For a 3.5" SAS backplane, route the SAS B cable through the cable
guides on the inner side of the chassis, and connect the SAS B cable
connector to the SAS B connector on the backplane. See Figure 3-23.
4 Close the system. See "Closing the System" on page 86.
5 Place the system upright and on its feet on a flat, stable surface.
6 Rotate the system feet outward.
7 Reattach any peripherals, then connect the system to the electrical outlet.
8 Turn on the system and attached peripherals.
9 Install any device drivers required for the card as described in the
documentation for the card.
book.book Page 134 Monday, June 15, 2009 11:33 AM

Dell PowerEdge T710 Specifications

General

Tcase	76 °C
Bus type	QPI
Stepping	D0
FSB Parity	No
Processor code	SLBF8
Processor cache	4 MB
Processor cores	4
Processor model	E5506
System bus rate	4.8 GT/s
Processor series	Intel Xeon 5500 Series
Processor socket	Socket B (LGA 1366)
Processor codename	Nehalem EP
Motherboard chipset	Intel® 5520
Number of QPI links	2
Processor frequency	2.13 GHz
Processor cache type	Smart Cache
Processor lithography	45 nm
Processor system type	DP
Processor manufacturer	Intel
Processor package size	42.5 x 45 mm
Processor front side bus	- MHz
Processor operating modes	64-bit
ECC supported by processor	Yes
Thermal Design Power (TDP)	80 W
Compatible processor series	Intel® Xeon®
Number of processors installed	1
CPU multiplier (bus/core ratio)	16
Memory types supported by processor	DDR3-SDRAM
Memory channels supported by processor	Triple
Memory clock speeds supported by processor	800 MHz
Memory bandwidth supported by processor (max)	19.2 GB/s
Maximum internal memory supported by processor	144 GB
HDD size	3.5 \
HDD speed	15000 RPM
HDD interface	Serial Attached SCSI (SAS)
Optical drive type	DVD-ROM
Total storage capacity	300 GB
Maximum storage capacity	- TB
Number of HDDs supported	6
Graphics card	G200
Graphics card family	Matrox
Memory slots	18x DIMM
Internal memory	4 GB
Memory clock speed	1333 MHz
Maximum internal memory	192 GB
Memory layout (slots x size)	2 x 2 GB
Networking features	Gigabit Ethernet
PS/2 ports quantity	0
USB 2.0 ports quantity	8
PCI Express x8 slots	5
Power supply	1100 W
Number of power supply units	-
Compatible operating systems	Windows Small Business Server 2011 Windows Small Business Server 2008 Windows Server 2008 SP2, x86/x64 (x64 includes Hyper-V) Windows Server 2008 R2 SP1, x64 (includes Hyper-V v2) Windows HPC Server 2008 Novell SUSE Linux Enterprise Server Red Hat Enterprise Linux
Sustainability certificates	ENERGY STAR
Compliance industry standards	IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Chassis type	Tower (5U)
Processor ARK ID	37096

Weight and Dimensions

Depth	731.8 mm
Width	217.9 mm
Height	466.3 mm
Weight	35300 g